Ändra sökning
Länk till posten
Permanent länk

Direktlänk
Publikationer (10 of 13) Visa alla publikationer
Vestman, V. (2023). I-girder Composite Bridges with Lateral Bracing: Improved load distribution. (Licentiate dissertation). Luleå: Luleå University of Technology
Öppna denna publikation i ny flik eller fönster >>I-girder Composite Bridges with Lateral Bracing: Improved load distribution
2023 (Engelska)Licentiatavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

This thesis deals with the subject of lateral bracing between the bottom flanges of I-girder composite bridges. The focus is on the impact of adding lateral bracing on existing bridges, as well as on new bridges. Experience and knowledge from bridge projects around the world are investigated and implemented in the evaluation of the research subject.

Many existing bridges are in need of being strengthened or replaced, due to the increased traffic volume and heavier traffic loads. Different approaches can be used to prolong the lifetime of existing bridges. The approach is different depending on the cause, but for increasing the lifetime regarding fatigue some of the most suitable options are described in this thesis. A proposed concept is presented, in this thesis, along with some research questions to be answered.

The use of lateral bracings in composite bridges varies between different parts of the world. In one country it can be a requirement/common praxis for long span composite bridges with two I-girders, in other countries there are no requirements of using them. Some parts of these regulations and requirements can be traced back to the tradition in both manufacturing and construction of this type of bridges. This thesis investigates how lateral bracing is used around the world to distribute eccentric loads between primary longitudinal structural members, provide resistance to lateral loads, and to permit an existing two-girder structural system to be retrofitted to behave similarly to an often more expensive closed steel box girder.

Furthermore, several case studies have been conducted to investigate the impact on the structural behavior of composite bridges where a lateral bracing is implemented in the structure. The results from these case studies are presented in the thesis and show the advantages of the quasi-box section for which the lateral bracing is closing the composite cross section. By making the I-girder composite cross section acting more like a box-section, the distribution of eccentric loads between the girders is improved. The impact on longitudinal stresses from traffic loads and the additional effects on internal sectional parts are also evaluated and discussed.

Furthermore, proposals of the connection design for lateral bracings in existing bridges are suggested. Finally, conclusions from the results are stated.

Ort, förlag, år, upplaga, sidor
Luleå: Luleå University of Technology, 2023
Serie
Licentiate thesis / Luleå University of Technology, ISSN 1402-1757
Nyckelord
assessment, bridge, composite bridge, steel-concrete composite, I-girder, case study, horizontal trusses, lateral bracing, rehabilitation, strengthening, torsional stiffness, upgrading
Nationell ämneskategori
Infrastrukturteknik
Forskningsämne
Byggkonstruktion
Identifikatorer
urn:nbn:se:ltu:diva-96212 (URN)978-91-8048-286-8 (ISBN)978-91-8048-287-5 (ISBN)
Presentation
2023-05-12, F1031, Luleå tekniska universitet, Luleå, 10:00 (Engelska)
Opponent
Handledare
Tillgänglig från: 2023-03-22 Skapad: 2023-03-22 Senast uppdaterad: 2023-12-18Bibliografiskt granskad
Vestman, V., García Jordan, F. J., Santamaría Caballero, G. & Collin, P. (2023). Lateral trusses between I-girders introducing torsional stiffness to a composite bridge in Guatemala. In: Milan Veljkovic; Trayana Tankova; Florentia Kavoura; Andreas Taras; Vlad Silvestru; Valentino Vigneri (Ed.), Eurosteel 2023: September 12–14, 2023, Amsterdam. Paper presented at 10th Eurosteel conference, (EUROSTEEL2023), Amsterdam, Netherlands, September 12-14, 2023 (pp. 1049-1054). John Wiley & Sons
Öppna denna publikation i ny flik eller fönster >>Lateral trusses between I-girders introducing torsional stiffness to a composite bridge in Guatemala
2023 (Engelska)Ingår i: Eurosteel 2023: September 12–14, 2023, Amsterdam / [ed] Milan Veljkovic; Trayana Tankova; Florentia Kavoura; Andreas Taras; Vlad Silvestru; Valentino Vigneri, John Wiley & Sons, 2023, s. 1049-1054Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

The ways of designing and building steel girder bridges with a composite concrete deck vary much between different parts of the world. A bridge system with twin steel I-girders or a concept with multiple (more than two) girders can be used. The design and use of details and secondary systems also vary a lot. In order to give horizontal stabilization and distribute horizontal loads, bracing between the I-girders bracings are often used. Although not so common, the bracing can also be used to distribute vertical loads between the main girders. To describe and to analyze the possible impact from using a lateral bracing, this paper describes the design of a curved bridge in Guatemala City and its challenges. The new Bridge over the Pinula River is designed as a steel-concrete composite bridge with multiple steel girders with a concrete deck on top and has lateral bracing between the girders. The bridge is used as a case study to analyze the impact from a lateral bracing system on the vertical load distribution between the longitudinal girders. The bridge was designed with lateral bracing between the top flanges along the whole bridge and with bracing between the lower flanges near the supports. The case study shows that the distribution of eccentric vertical loads between the longitudinal girders can be improved by using lateral bracing between the lower flanges for multiple girders. In some cases, it may not be beneficial to use lateral bracings along the whole bridge length, like for example this bridge. In this case due to the governing design cases in the construction stages where these bracings influenced the torsional stiffness of the bridge in such way that an unfavorable distribution of the support reactions between the six girders at some supports was achieved.

Ort, förlag, år, upplaga, sidor
John Wiley & Sons, 2023
Serie
c/e papers - Proceedings in civil engineering, E-ISSN 2509-7075 ; 6
Nyckelord
Bridge, I-girder, lateral bracing, launching, steel-concrete composite, torsional stiffness
Nationell ämneskategori
Infrastrukturteknik
Forskningsämne
Byggkonstruktion
Identifikatorer
urn:nbn:se:ltu:diva-96210 (URN)10.1002/cepa.2684 (DOI)
Konferens
10th Eurosteel conference, (EUROSTEEL2023), Amsterdam, Netherlands, September 12-14, 2023
Anmärkning

Full text license: CC BY

Tillgänglig från: 2023-03-22 Skapad: 2023-03-22 Senast uppdaterad: 2023-11-24Bibliografiskt granskad
Vestman, V., Collin, P., Lilja, H., Tirkkonen, T., Peltomaa, M., Jordan, J., . . . Hällmark, R. (2022). Horizontal bracing in steel I-girder bridges with composite concrete decks. In: František Wald, Pavel Ryjáček (Ed.), IABSE Symposium Prague 2022: Challenges for Existing and Oncoming Structures - Report, International Association for Bridge and Structural Engineering: . Paper presented at IABSE Symposium Prague 2022: Challenges for Existing and Oncoming Structures, Prague, Czech Republic, May 25-27, 2022 (pp. 1684-1690). International Association for Bridge and Structural Engineering
Öppna denna publikation i ny flik eller fönster >>Horizontal bracing in steel I-girder bridges with composite concrete decks
Visa övriga...
2022 (Engelska)Ingår i: IABSE Symposium Prague 2022: Challenges for Existing and Oncoming Structures - Report, International Association for Bridge and Structural Engineering / [ed] František Wald, Pavel Ryjáček, International Association for Bridge and Structural Engineering, 2022, s. 1684-1690Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

This paper treats the use of horizontal trusses between the bottom flanges of new I-girder bridges, to create a box-like behaviour. In contrast to the general vertical cross frames of an I-girder bridge, the horizontal trusses bring along substantial torsional stiffness of the cross section of a bridge. The concept gives large advantages when it comes to fatigue caused by eccentric loading, since the I-girders will share the load more equally. The concept is exemplified by bridges in Finland, Guatemala and France, and some design aspects as well as practical aspects are discussed. 

Ort, förlag, år, upplaga, sidor
International Association for Bridge and Structural Engineering, 2022
Nyckelord
box action, bracings, bridge fatigue, I-girders bridges, trusses
Nationell ämneskategori
Tillförlitlighets- och kvalitetsteknik
Forskningsämne
Byggkonstruktion
Identifikatorer
urn:nbn:se:ltu:diva-92201 (URN)10.2749/prague.2022.1684 (DOI)2-s2.0-85133509021 (Scopus ID)
Konferens
IABSE Symposium Prague 2022: Challenges for Existing and Oncoming Structures, Prague, Czech Republic, May 25-27, 2022
Anmärkning

ISBN for host publication: 978-3-85748-181-9

Tillgänglig från: 2022-07-19 Skapad: 2022-07-19 Senast uppdaterad: 2023-09-13Bibliografiskt granskad
Vestman, V., Collin, P. & Hällmark, R. (2022). Strengthening of a Composite I-girder Bridge by Trusses Introducing Box-Action. In: : . Paper presented at 10th International symposium on steel bridges – for A Green Planet, September 20 - 22, 2022 Istanbul, Turkey.
Öppna denna publikation i ny flik eller fönster >>Strengthening of a Composite I-girder Bridge by Trusses Introducing Box-Action
2022 (Engelska)Konferensbidrag, Enbart muntlig presentation (Övrigt vetenskapligt)
Abstract [en]

The increased amount of traffic and the increasingly heavier loads on the road network push the existing infrastructure to its design limit. Bridges, which are an important part of the road network, need to be adopted to the new traffic demands regarding both the load capacity and the fatigue limit state, FLS. Steel-concrete composite bridges, with twin steel I-girders, is a common bridge type in the Nordic countries. These bridges are often designed using beam models, assuming that the concrete deck is a statically determinate structure supported on the two steel girders in the transversal direction. This assumption implies that the most loaded girder can sometimes be subjected to even more than 100% of an eccentric load, e.g., the traffic loads in the design codes. If the girders are strengthened to be able to share the eccentric loads more equally, it would have a significant impact on the load capacity, especially for the fatigue limit state. By introducing horizontal trusses between the bottom flanges of the girders, making the cross-section act more like a box-girder, the torsional stiffness will increase so that the girders will share the eccentric loads more equally. The bracing system of the trusses can be designed in different shapes, each of them with pros and cons for the existing bridge structure. In this paper, the effects from different shapes of the bracing are evaluated of a single span I-girder composite bridge. The increased torsional stiffness and the change of the internal shear flow will increase the load capacity of the steel girders.

Nyckelord
bridge, steel-concrete composite, I-girder, case study, horizontal trusses, torsional stiffness, strengthening, composite bridges
Nationell ämneskategori
Infrastrukturteknik
Forskningsämne
Byggkonstruktion
Identifikatorer
urn:nbn:se:ltu:diva-96211 (URN)
Konferens
10th International symposium on steel bridges – for A Green Planet, September 20 - 22, 2022 Istanbul, Turkey
Tillgänglig från: 2023-03-22 Skapad: 2023-03-22 Senast uppdaterad: 2023-09-05
Vestman, V., Collin, P. & Oudomphanh, S. (2022). Torsion of a Norwegian bridge with partial box-action - a case study. In: IABSE Symposium Prague 2022: Challenges for Existing and Oncoming Structures - Report: . Paper presented at IABSE Symposium Prague 2022: Challenges for Existing and Oncoming Structures, Prague, Czech Republic, May 25-27, 2022. International Association for Bridge and Structural Engineering
Öppna denna publikation i ny flik eller fönster >>Torsion of a Norwegian bridge with partial box-action - a case study
2022 (Engelska)Ingår i: IABSE Symposium Prague 2022: Challenges for Existing and Oncoming Structures - Report, International Association for Bridge and Structural Engineering, 2022Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

Some old bridges have a truss between the bottom flanges not intended for torsional effects but for transferring horizontal forces. This paper describes the effects of the truss on torsion for a Norwegian three span bridge from 1967, without composite action. Furthermore, the effects of post-installed shear connectors are investigated. For composite bridges without intended composite action in bending, the effects of the slab preventing the top flanges from moving laterally should not be ignored, since this is important for the deformations of the girders under eccentric loading. Furthermore, the load distribution between the girders for an eccentric load is significantly enhanced if the horizontal truss is considered. The paper also investigates and presents the effects of post-installed shear connectors, with respect to bending stresses in the bottom flanges (moderate effects) and the top flange (large effects). 

Ort, förlag, år, upplaga, sidor
International Association for Bridge and Structural Engineering, 2022
Nyckelord
Composite bridge, strengthening, horisontal bracing, composite action, box-action
Nationell ämneskategori
Annan samhällsbyggnadsteknik
Forskningsämne
Byggkonstruktion
Identifikatorer
urn:nbn:se:ltu:diva-91424 (URN)2-s2.0-85133548852 (Scopus ID)
Konferens
IABSE Symposium Prague 2022: Challenges for Existing and Oncoming Structures, Prague, Czech Republic, May 25-27, 2022
Tillgänglig från: 2022-06-15 Skapad: 2022-06-15 Senast uppdaterad: 2023-09-05Bibliografiskt granskad
Vestman, V., Collin, P., Hällmark, R. & Arason, M. (2021). Monitoring of a Norwegian steel-concrete bridge strengthening forcomposite action. In: Snijder H.H.; De Pauw, B.; van Alphen, S.; Mengeot, P. (Ed.), IABSE Congress Ghent 2021: Structural Engineering for Future Societal Needs. Paper presented at IABSE Congress 2021: Structural Engineering for Future Societal Needs, Ghent, Belgium [Online], September 22-24, 2021 (pp. 1709-1717). International Association for Bridge and Structural Engineering (IABSE)
Öppna denna publikation i ny flik eller fönster >>Monitoring of a Norwegian steel-concrete bridge strengthening forcomposite action
2021 (Engelska)Ingår i: IABSE Congress Ghent 2021: Structural Engineering for Future Societal Needs / [ed] Snijder H.H.; De Pauw, B.; van Alphen, S.; Mengeot, P., International Association for Bridge and Structural Engineering (IABSE) , 2021, s. 1709-1717Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

Traffic density and vehicle weight have been increasing over time, which implies that many existing road bridges were not designed for the high service loads and the increased number of load cycles that they are exposed to today. One way to increase the traffic load capacity of non-composite steel-concrete bridges is to use post-install shear connectors and one type of shear connector is the coiled spring pin. This type of connector has advantages for strengthening of existing bridges, since it enables an installation from below while the bridge is still in service and does not bring along removal of concrete and pavement, nor welding to the top flange.

This paper describes one ~50 years old Norwegian single span steel-concrete bridge that was strengthened with post-installed coiled spring pins. The strengthening method and the design procedure are presented, along with the results from a field monitoring on Sagstu bridge, performed to evaluate the behaviour of the strengthened structure. The results show that the coiled spring pins counteract the slip and bring along a very good degree of composite action.

Ort, förlag, år, upplaga, sidor
International Association for Bridge and Structural Engineering (IABSE), 2021
Serie
IABSE Congress Reports ; 21
Nyckelord
composite bridges, coiled spring pins, monitoring, post-installed shear connectors
Nationell ämneskategori
Infrastrukturteknik
Forskningsämne
Byggkonstruktion
Identifikatorer
urn:nbn:se:ltu:diva-87390 (URN)10.2749/ghent.2021.1709 (DOI)2-s2.0-85119058194 (Scopus ID)
Konferens
IABSE Congress 2021: Structural Engineering for Future Societal Needs, Ghent, Belgium [Online], September 22-24, 2021
Anmärkning

ISBN för värdpublikation: 978-3-85748-176-5

Tillgänglig från: 2021-10-06 Skapad: 2021-10-06 Senast uppdaterad: 2023-09-05Bibliografiskt granskad
Svensson, D., Vestman, V. & Collin, P. (2021). Slussen – the lock of Stockholm. In: H. H. (Bert) Snijder; Bart De Pauw; Sander van Alphen; Pierre Mengeot (Ed.), IABSE Congress Ghent 2021: Structural Engineering for Future Societal Needs. Paper presented at IABSE Congress 2021: Structural Engineering for Future Societal Needs, Ghent, Belgium, September 22-24, 2021 (pp. 1882-1890). International Association for Bridge and Structural Engineering (IABSE)
Öppna denna publikation i ny flik eller fönster >>Slussen – the lock of Stockholm
2021 (Engelska)Ingår i: IABSE Congress Ghent 2021: Structural Engineering for Future Societal Needs / [ed] H. H. (Bert) Snijder; Bart De Pauw; Sander van Alphen; Pierre Mengeot, International Association for Bridge and Structural Engineering (IABSE) , 2021, s. 1882-1890Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

Slussen is situated in the inner city of Stockholm just south of the world heritage site Gamla Stan and the royal castle. This historical site and also second biggest traffic and transportation hub in Stockholm is at the moment undergoing a complete refurbishment due to new demands and requirements and due to the fact that the former traffic plant was in a very bad shape with severe settlements and outworn concrete structures. The old traffic structure from the 1930´s is replaced by a modern urban space and transportation node designed by Foster + Partner and Berg arkitekter, adopted to demands and requirements of the future i.e. increased capacity for pedestrians and cyclists, heavily increased discharge capacity for Lake Mälaren, attractive areas for the public close to the water and several restaurants and cafés.

This mega project ( 1.4 Billion) cannot be described completely in a single paper so therefore twoobjects of special technical interest have been chosen and are described below: the water regulationsystem as well as the unique 3.400 Tons steel bridge, transported in one piece from China.

Ort, förlag, år, upplaga, sidor
International Association for Bridge and Structural Engineering (IABSE), 2021
Nyckelord
Large infrastructure projects, lock canal, steel bridge, orthotropic deck & sea transport
Nationell ämneskategori
Infrastrukturteknik
Forskningsämne
Byggkonstruktion
Identifikatorer
urn:nbn:se:ltu:diva-87391 (URN)10.2749/ghent.2021.1882 (DOI)2-s2.0-85119060528 (Scopus ID)
Konferens
IABSE Congress 2021: Structural Engineering for Future Societal Needs, Ghent, Belgium, September 22-24, 2021
Tillgänglig från: 2021-10-06 Skapad: 2021-10-06 Senast uppdaterad: 2023-09-05Bibliografiskt granskad
Hällmark, R., Nilforoush, R., Vestman, V. & Collin, P. (2021). Testing of composite girders with coiled spring pin shear connectors. In: H. H. (Bert) Snijder; Bart De Pauw; Sander van Alphen; Pierre Mengeot (Ed.), IABSE Congress Ghent 2021: Structural Engineering for Future Societal Needs. Paper presented at IABSE Congress 2021: Structural Engineering for Future Societal Needs, Ghent, Belgium, 22-24 September, 2021 (pp. 1700-1708). International Association for Bridge and Structural Engineering (IABSE)
Öppna denna publikation i ny flik eller fönster >>Testing of composite girders with coiled spring pin shear connectors
2021 (Engelska)Ingår i: IABSE Congress Ghent 2021: Structural Engineering for Future Societal Needs / [ed] H. H. (Bert) Snijder; Bart De Pauw; Sander van Alphen; Pierre Mengeot, International Association for Bridge and Structural Engineering (IABSE) , 2021, s. 1700-1708Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

Today, steel girder bridges with concrete deck slabs are generally constructed as steel-concrete composite structures, to utilize the material and the structural parts in an efficient way. However, many existing bridges constructed before the early 1980´s were designed without shear connectors at the steel-concrete interface. With increasing traffics loads and higher amount of load cycles, there is sometimes a need to strengthen these bridges. One way to increase the bending moment capacity is to create composite action by post-installation of shear connectors. The authors have studied the concept of strengthening by post-installed shear connectors, with a focus on a connector called coiled spring pin. This paper presents the results from the first beam tests performed with this kind of shear connector. In line with the previous push-out tests, the test results indicate a very ductile shear connection, with a potential to be a material- and cost-efficient strengthening alternative.

Ort, förlag, år, upplaga, sidor
International Association for Bridge and Structural Engineering (IABSE), 2021
Nyckelord
bridge, strengthening, rehabilitation, shear connector, test, composite girder, coiled spring pin
Nationell ämneskategori
Infrastrukturteknik
Forskningsämne
Byggkonstruktion
Identifikatorer
urn:nbn:se:ltu:diva-87385 (URN)10.2749/ghent.2021.1700 (DOI)2-s2.0-85119084525 (Scopus ID)
Konferens
IABSE Congress 2021: Structural Engineering for Future Societal Needs, Ghent, Belgium, 22-24 September, 2021
Forskningsfinansiär
TrafikverketSvenska Byggbranschens Utvecklingsfond (SBUF)
Tillgänglig från: 2021-10-05 Skapad: 2021-10-05 Senast uppdaterad: 2023-09-05Bibliografiskt granskad
Arason, M., Bie Gundersen, E., Collin, P. & Vestman, V. (2020). Innovasjon i bruforsterkning i Agder. Nyheter om stålbyggnad, 2020(4), 24-26
Öppna denna publikation i ny flik eller fönster >>Innovasjon i bruforsterkning i Agder
2020 (Norska)Ingår i: Nyheter om stålbyggnad, ISSN 1404-9414, Vol. 2020, nr 4, s. 24-26Artikel i tidskrift (Övrigt vetenskapligt) Published
Abstract [no]

EFLA og Luleå Tekniska Universitet har bistått Agder fylkeskommune med forsterkning av to gamle stålbjelkebruer i Agder fylke, som dannet en flaskehals for vegtransport i området. I prosjekteringen er det brukt en metode som aldri har vært brukt i Norge før, og den har vist seg å være effektiv i forhold til kostnad, gjennomførbarhet og miljøpåvirkning. Prosjektet er et eksempel på vellykket nordisk samarbeid, og kan ha overføring til fremtidige prosjekter

Ort, förlag, år, upplaga, sidor
Stålbyggnadsinstitutet, 2020
Nationell ämneskategori
Infrastrukturteknik
Forskningsämne
Byggkonstruktion
Identifikatorer
urn:nbn:se:ltu:diva-87571 (URN)
Anmärkning

Godkänd;2021;Nivå 0;2021-10-21 (alebob)

Tillgänglig från: 2021-10-21 Skapad: 2021-10-21 Senast uppdaterad: 2023-09-05Bibliografiskt granskad
Bäck, L., Svensson, D. & Vestman, V. (2020). Slussenbron - en avancerad stålkonstruktion med ett speciellt montage. Tidningen Stålbyggnad (1), 36-39
Öppna denna publikation i ny flik eller fönster >>Slussenbron - en avancerad stålkonstruktion med ett speciellt montage
2020 (Svenska)Ingår i: Tidningen Stålbyggnad, ISSN 1404-9414, nr 1, s. 36-39Artikel i tidskrift (Övrig (populärvetenskap, debatt, mm)) Published
Ort, förlag, år, upplaga, sidor
Stockholm: Stålbyggnadsinstitutet, 2020
Nationell ämneskategori
Infrastrukturteknik
Identifikatorer
urn:nbn:se:ltu:diva-96215 (URN)
Anmärkning

Godkänd;2023;Nivå 0;2023-07-04 (hanlid)

Tillgänglig från: 2023-03-22 Skapad: 2023-03-22 Senast uppdaterad: 2023-12-12Bibliografiskt granskad
Organisationer
Identifikatorer
ORCID-id: ORCID iD iconorcid.org/0000-0002-9627-4713

Sök vidare i DiVA

Visa alla publikationer