Change search
Link to record
Permanent link

Direct link
BETA
Liang, Jiang
Alternative names
Publications (2 of 2) Show all publications
Xue, P., Yang, Q., Liu, G., Han, F. L., Liang, J., Engström, F. & Björkman, B. (2017). Air Quenching of Steel slag to Enhance its Hydraulic Activity for Recycling the Slag as Meterials in Cement and Concrete Applications. Paper presented at 2016 International Conference on Material Science and Engineering Technology, ICMSET 2016, Phuket, Thailand, 14-16 October 2016. Key Engineering Materials, 737, 488-493
Open this publication in new window or tab >>Air Quenching of Steel slag to Enhance its Hydraulic Activity for Recycling the Slag as Meterials in Cement and Concrete Applications
Show others...
2017 (English)In: Key Engineering Materials, ISSN 1013-9826, E-ISSN 1662-9795, Vol. 737, p. 488-493Article in journal (Refereed) Published
Abstract [en]

A steel slag has been treated by air granulation, in order to enhance cementitious properties of the slag. Two samples with sizes ranged 1.68-2.38mm and 212-297μm and coded as Slag A and Slag B, respectively, were chosen from the granulated slag for investigations. A sample of the original steel slag was also studied. XRD analyses indicated the formations of α-C2S, β-C2S, C2F, C2MS2, f-MgO and α-C2S, C2F, f-MgO in Slag A and Slag B, respectively. The phases in the two slag samples were quite different from the phases found in steel slag. The SEM results show a reduction of C2S sizes from 10-20μm for the steel slag to nano-scales by air quenching for Slag B. This treatment of air quenching has increased the cumulative heat of hydration to 105.35J/g measured for Slag B, almost two times greater than that of the steel slag. The study results demonstrate a high potential for utilizations of the steel slag in cement and concrete applications after the slag treatment by air quenching. The treatment may thus lead to an environmental friendly and cost-effective recycling for the steel slag. This can also contribute to the sustainable developments in the steel and cement/concrete industries.

Place, publisher, year, edition, pages
Trans Tech Publications, 2017
National Category
Metallurgy and Metallic Materials
Research subject
Process Metallurgy
Identifiers
urn:nbn:se:ltu:diva-63511 (URN)10.4028/www.scientific.net/KEM.737.488 (DOI)2-s2.0-85027060966 (Scopus ID)
Conference
2016 International Conference on Material Science and Engineering Technology, ICMSET 2016, Phuket, Thailand, 14-16 October 2016
Note

Konferensartikel i tidskrift

Available from: 2017-05-23 Created: 2017-05-23 Last updated: 2017-11-28Bibliographically approved
Jia, Q., Yang, Q., Guo, L., Knutsson, S., Xue, P., Liu, G. & Jiang, L. (2016). Effects of fine content, binder type and porosity on mechanical properties of cemented paste backfill with co-deposition of tailings sand and smelter slag. The Electronic journal of geotechnical engineering, 21(20), 6971-6988
Open this publication in new window or tab >>Effects of fine content, binder type and porosity on mechanical properties of cemented paste backfill with co-deposition of tailings sand and smelter slag
Show others...
2016 (English)In: The Electronic journal of geotechnical engineering, ISSN 1089-3032, E-ISSN 1089-3032, Vol. 21, no 20, p. 6971-6988Article in journal (Refereed) Published
Abstract [en]

Mine backfilling is a process where the underground voids resulted from mining are filled with waste materials. The potential of co-depositing iron sand produced from smelting process with tailings sand was investigated in the present study. Different amounts of iron sand were mixed with the tailings sand to prepare cemented paste backfill (CPB) samples. Two types of binders were used. Uniaxial compression tests were performed for the CPB samples after 28 days of curing. The porosities of the samplers after curing were calculated to correlate the porosity with the uniaxial compression strength, UCS. Results from uniaxial compression tests showed that the amount of iron sand and the type of the binder influences the UCS, as well as content values of fines and porosity. These results demonstrated the possibility for a part of Fe-sand to be deposited together with the tailings sand to increase UCS values for the CPB samples, which will be beneficial for both mining operation and environmental protection.

Place, publisher, year, edition, pages
Mete Öner, 2016
National Category
Geotechnical Engineering Metallurgy and Metallic Materials
Research subject
Soil Mechanics; Process Metallurgy
Identifiers
urn:nbn:se:ltu:diva-60393 (URN)2-s2.0-84992520613 (Scopus ID)
Note

Validerad; 2016; Nivå 1; 2016-11-14 (andbra)

Available from: 2016-11-14 Created: 2016-11-14 Last updated: 2018-11-23Bibliographically approved
Organisations

Search in DiVA

Show all publications