Efficiency enhancement of hydrogen based electric powertrain is becoming highly relevant for medium to heavy duty transportation due to advantages of eminent electrochemical cell design and advances in infrastructure accessibility. Herein, a facile and highly effective fabrication process has been reported for the first time to demonstrate an outstanding mechanical strength and electrical conductivity simultaneously in the carbon rich composite designed to enhance the fuel cell performance. Improvement of composites with different advanced reinforced materials such as carbon veil, recycled carbon fiber as well as functional additives such as carbon black, multiwalled nanotube, etc. Was investigated through a holistic approach of optimized parameters. Advanced composite plates have been designed to be mechanically flexible, electrically conductive and cost effective; this newly designed composite for bipolar plate supersedes by far the US Department of Energy (DOE) target for fuel cell bipolar plate with a flexural strength of over 64 MPa and exceeding electrical conductivity of 200 S/cm. Notably, tuned process parameters as well as novel architecture of materials such as continuous carbon fiber and carbon veil can facilitate the fabrication of a light-weight high-performance carbon polymer composite for a wide range of applications including battery electrodes, supercapacitors, fuel cells and solar cell.

The skin is the largest organ of the human body. Wounds disrupt the functions of the skin and can have catastrophic consequences for an individual resulting in significant morbidity and mortality. Wound infections are common and can substantially delay healing and can result in non-healing wounds and sepsis. Early diagnosis and treatment of infection reduce risk of complications and support wound healing. Methods for monitoring of wound pH can facilitate early detection of infection. Here we show a novel strategy for integrating pH sensing capabilities in state-of-the-art hydrogel-based wound dressings fabricated from bacterial nanocellulose (BC). A high surface area material was developed by self-assembly of mesoporous silica nanoparticles (MSNs) in BC. By encapsulating a pH-responsive dye in the MSNs, wound dressings for continuous pH sensing with spatiotemporal resolution were developed. The pH responsive BC-based nanocomposites demonstrated excellent wound dressing properties, with respect to conformability, mechanical properties, and water vapor transmission rate. In addition to facilitating rapid colorimetric assessment of wound pH, this strategy for generating functional BC-MSN nanocomposites can be further be adapted for encapsulation and release of bioactive compounds for treatment of hard-to-heal wounds, enabling development of novel wound care materials.

Hydrogels of cellulose nanofibrils (CNFs) are promising wound dressing candidates due to their biocompatibility, high water absorption, and transparency. Herein, two different commercially available wood species, softwood and hardwood, were subjected to TEMPO-mediated oxidation to proceed with delignification and oxidation in a one-pot process, and thereafter, nanofibrils were isolated using a high-pressure microfluidizer. Furthermore, transparent nanofibril hydrogel networks were prepared by vacuum filtration. Nanofibril properties and network performance correlated with oxidation were investigated and compared with commercially available TEMPO-oxidized pulp nanofibrils and their networks. Softwood nanofibril hydrogel networks exhibited the best mechanical properties, and in vitro toxicological risk assessment showed no detrimental effect for any of the studied hydrogels on human fibroblast or keratinocyte cells. This study demonstrates a straightforward processing route for direct oxidation of different wood species to obtain nanofibril hydrogels for potential use as wound dressings, with softwood having the most potential.

This study aimed to develop a manufacturing process for recycled textile long fiber thermoplastics (RT-LFT) and thereby contribute to circular economy. Three different post-consumer textiles (cotton denim and plain weave, and silk plain weave) were cut into strips and fed directly into a co-rotating twin-screw extruder in which the textile was fibrillated and compounded with polypropylene (PP). The fibrillation of the textile, fiber dispersion, and interaction with the matrix polymer were studied, and the thermal and mechanical properties of the composites were evaluated. For example, cotton denim composites containing 30 wt% fiber content resulted in 26% increase in yield strength and a 72% increase in modulus when compared with that of PP. The RT-LFT process is a straightforward method for transforming used textiles into composites like cups and bottoms, offering advantages such as reduced manufacturing costs, add value for waste material, and lower carbon emissions.

The self-assembly of nanocellulose in the form of cellulose nanofibers (CNFs) can be accomplished via hydrogen-bonding assistance into completely bio-based hydrogels. This study aimed to use the intrinsic properties of CNFs, such as their ability to form strong networks and high absorption capacity and exploit them in the sustainable development of effective wound dressing materials. First, TEMPO-oxidized CNFs were separated directly from wood (W-CNFs) and compared with CNFs separated from wood pulp (P-CNFs). Second, two approaches were evaluated for hydrogel self-assembly from W-CNFs, where water was removed from the suspensions via evaporation through suspension casting (SC) or vacuum-assisted filtration (VF). Third, the W-CNF-VF hydrogel was compared to commercial bacterial cellulose (BC). The study demonstrates that the self-assembly via VF of nanocellulose hydrogels from wood was the most promising material as wound dressing and displayed comparable properties to that of BC and strength to that of soft tissue.

Polylactic acid (PLA) is a biopolymer that has potential for use in food packaging applications; however, its low crystallinity and poor gas barrier properties limit its use. This study aimed to increase the understanding of the structure property relation of biopolymer blends and their nanocomposites. The crystallinity of the final materials and their effect on barrier properties was studied. Two strategies were performed: first, different concentrations of poly(hydroxybutyrate) (PHB; 10, 25, and 50 wt %) were compounded with PLA to facilitate the PHB spherulite development, and then, for further increase of the overall crystallinity, glycerol triacetate (GTA) functionalized chitin nano crystals (ChNCs) were added. The PLA:PHB blend with 25 wt % PHB showed the formation of many very small PHB spherulites with the highest PHB crystallinity among the examined compositions and was selected as the matrix for the ChNC nanocomposites. Then, ChNCs with different concentrations (0.5, 1, and 2 wt %) were added to the 75:25 PLA:PHB blend using the liquid-assisted extrusion process in the presence of GTA. The addition of the ChNCs resulted in an improvement in the crystallization rate and degree of PHB crystallinity as well as mechanical properties. The nanocomposite with the highest crystallinity resulted in greatly decreased oxygen (O) and carbon dioxide (CO2) permeability and increased the overall mechanical properties compared to the blend with GTA. This study shows that the addition ChNCs in PLA:PHB can be a possible way to reach suitable gas barrier properties for food packaging films.

Cellulose nanofibrils can be derived from the native load-bearing cellulose microfibrils in wood. These microfibrils are synthesized by a cellulose synthase enzyme complex that resides in the plasma membrane of developing wood cells. It was previously shown that transgenic hybrid aspen trees with reduced expression of CSI1 have different wood mechanics and cellulose microfibril properties. We hypothesized that these changes in the native cellulose may affect the quality of the corresponding nanofibrils. To test this hypothesis, wood from wild-type and transgenic trees with reduced expression of CSI1 was subjected to oxidative nanofibril isolation. The transgenic wood-extracted nanofibrils exhibited a significantly lower suspension viscosity and estimated surface area than the wild-type nanofibrils. Furthermore, the nanofibril networks manufactured from the transgenics exhibited high stiffness, as well as reduced water uptake, tensile strength, strain-to-break, and degree of polymerization. Presumably, the difference in wood properties caused by the decreased expression of CSI1 resulted in nanofibrils with distinctive qualities. The observed changes in the physicochemical properties suggest that the differences were caused by changes in the apparent nanofibril aspect ratio and surface accessibility. This study demonstrates the possibility of influencing wood-derived nanofibril quality through the genetic engineering of trees.

The structural changes of the glucopyranose chain and the chemical compositional response of cellulose nanofibers (CNFs) under thermal exposure (at 190 °C for 5 h) have remained a significant gap in the understanding of the long-term performance of nanocellulose. Herein, CNF films with different chemical compositions were investigated to confirm the structural transformation of glucopyranose (coupling constant of OH groups changed up to 50%) by nuclear magnetic resonance (NMR) analysis. Remarkably, the glucopyranose rings underwent partial dehydration during the thermal exposure resulting in enol formation. This study confirms the chain mobility that could lead to the conformational and dimensional changes of the CNFs during thermal exposure. The broad range of conformations was defined by the dihedral angles that varied from ±27° to ±139° after thermal exposure. Investigation into the mechanism involving chemical transformation of the substrates during heating is important for the fabrication of the next generation of flexible electrical materials.