Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Wear of teeth of circular saw blades
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknik.ORCID-id: 0000-0002-0145-080X
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknik.
2011 (engelsk)Konferansepaper, Poster (with or without abstract) (Fagfellevurdert)
Abstract [en]

Measured wear data is presented for 3 different carbide grades. The data were collected during rip sawing wood with a double arbour saw. The purpose of the test was to determine the suitability of different grades for sawing frozen timber. A set of circular saw blades of diameter 350 mm was equipped with teeth comprised of 3 different cemented carbide grades, denoted A, B and C. These 3 grades were chosen out of 6 grades in an earlier preliminary laboratory test. Grade A was a relatively soft and tough standard grade (K1C=17, HV30=1150) normally used in sawmills in winter conditions for frozen wood, grade B was harder and more brittle (K1C=11, HV30=1600) and grade C was even harder and more brittle (K1C=9.5, HV30=1950). The double arbour saw (with vertical arbours) was equipped with 6 saw blades (3 on each arbour) for cutting 2 centre boards and 2 side boards. The 6 saw blades with different teeth were mounted in a mixed manner on the arbours, and after sawing a number of logs the wear of teeth was measured. After some time the blades were removed, inspected, ground and used again for sawing. The thickness of boards was also measured and the standard deviation was calculated.The results show cutting edge radii as a function of the number of logs sawn and also the standard deviation of the thickness of the sawn boards. Grade A had the highest wear and grades B and C the lowest wear. There was no significant edge damage during the tests. Grade C did not suffer problems of chipping from cutting edges and was found to be suitable for sawing frozen timber. The thickness standard deviations were constant at about 0.2 mm, and not a function of the number of logs sawn.

sted, utgiver, år, opplag, sider
2011.
HSV kategori
Forskningsprogram
Träteknik
Identifikatorer
URN: urn:nbn:se:ltu:diva-26952Lokal ID: 03990e33-80c0-4982-aea5-8c3726c25d16OAI: oai:DiVA.org:ltu-26952DiVA, id: diva2:1000133
Konferanse
International Wood Machining Seminar : 07/06/2011 - 10/06/2011
Merknad

Godkänd; 2011; 20110617 (matse)

Tilgjengelig fra: 2016-09-30 Laget: 2016-09-30 Sist oppdatert: 2022-10-13bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Person

Ekevad, MatsMarklund, BirgerCristovao, Luis

Søk i DiVA

Av forfatter/redaktør
Ekevad, MatsMarklund, BirgerCristovao, Luis
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar

urn-nbn

Altmetric

urn-nbn
Totalt: 53 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf