Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
A simplified analysis method for composite beams with interlayer slip
Department of TFE-Civil Engineering, Faculty of Science and Technology, Umeå University.ORCID-id: 0000-0002-0336-6433
2009 (engelsk)Inngår i: International Journal of Mechanical Sciences, ISSN 0020-7403, E-ISSN 1879-2162, Vol. 51, nr 7, s. 515-530Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

A simplified static procedure is proposed for analysing and designing composite beams with interlayer slip. The method is parallel to the Eurocode 5 method, but it is general in nature and can be applied to arbitrary boundary and loading conditions. In contrast with Eurocode 5, a general and correct way of choosing the effective beam length of the problem is given by the present procedure, which is that the effective beam length equals the buckling length that is found in the corresponding column buckling problem. The procedure predicts the deflections and internal actions and stresses, in principle by replacing the fully composite bending stiffness (EI) with the effective (partially) composite bending stiffness (EIeff) in the expressions for these quantities in the corresponding fully composite beam. This effective bending stiffness depends on two non-dimensional parameters: the composite action parameter (shear connection stiffness) and the relative bending stiffness parameter. The method is applied to a number of simple practical cases and the results obtained have been compared with the exact values. The applicability of the simplified analysis procedure was found to be very good, except for interlayer shear stresses. The error in the Eurocode 5 procedure, as compared with the method proposed in this paper, can in some cases be up to almost 30% depending on the boundary conditions

sted, utgiver, år, opplag, sider
2009. Vol. 51, nr 7, s. 515-530
HSV kategori
Forskningsprogram
Träteknik
Identifikatorer
URN: urn:nbn:se:ltu:diva-63407DOI: 10.1016/j.ijmecsci.2009.05.003Scopus ID: 2-s2.0-67650756424OAI: oai:DiVA.org:ltu-63407DiVA, id: diva2:1096361
Tilgjengelig fra: 2017-05-17 Laget: 2017-05-17 Sist oppdatert: 2017-11-24bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Personposter BETA

Girhammar, Ulf Arne

Søk i DiVA

Av forfatter/redaktør
Girhammar, Ulf Arne
I samme tidsskrift
International Journal of Mechanical Sciences

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 235 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf