Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Effects of molding temperature, pressure and time on polyvinyl alcohol nanocomposites properties produced by freeze drying technique
Department of Wood and Paper Science and Technology, Faculty of Natural Resources, University of Tehran, Karaj.
Food Science Department, Agriculture College, Isfahan University of Technology.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Materialvetenskap. Department of Wood and Paper Science and Technology, Faculty of Natural Resources, University of Tehran, Karaj.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Materialvetenskap.ORCID-id: 0000-0003-4762-2854
2018 (engelsk)Inngår i: Industrial crops and products (Print), ISSN 0926-6690, E-ISSN 1872-633X, Vol. 121, s. 1-9Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

The main aim of this study was to develop a novel approach to incorporate high cellulose nanofiber (CNF) loadings into polyvinyl alcohol (PVA) nanocomposites. The nanocomposites were prepared by freezing via liquid nitrogen and consequent freeze drying combined with hot press molding. To investigate the effect of the molding parameters on the morphological, mechanical and thermal properties, chemical structure and transparency of the PVA + CNF nanocomposites, two different mold pressures, temperatures and holding times were used for fabrication of PVA + CNF nanocomposites. The maximum tensile strength of 121 MPa of the PVA + CNF 20% nanocomposites was obtained when they were molded at 130 °C and 50 kPa for 7 min. Dynamic mechanical analysis showed that the storage modulus of the composites prepared at 130 °C and 50 kPa for 7 min is about 20% higher than nanocomposites molded at 150 °C and 150 kPa for 10 min. Optical properties (absorption spectra) of the PVA and PVA + CNF nanocomposites were increased as the mold pressures, temperature and holding time increased. Micrographs showed more sough fracture surface with increasing pressure and temperature during hot press molding.

sted, utgiver, år, opplag, sider
Elsevier, 2018. Vol. 121, s. 1-9
HSV kategori
Forskningsprogram
Trä och bionanokompositer
Identifikatorer
URN: urn:nbn:se:ltu:diva-68590DOI: 10.1016/j.indcrop.2018.04.079ISI: 000437996900001Scopus ID: 2-s2.0-85046705277OAI: oai:DiVA.org:ltu-68590DiVA, id: diva2:1203202
Merknad

Validerad;2018;Nivå 2;2018-05-02 (andbra)

Tilgjengelig fra: 2018-05-02 Laget: 2018-05-02 Sist oppdatert: 2018-08-08bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Personposter BETA

Jonoobi, MehdiOksman, Kristiina

Søk i DiVA

Av forfatter/redaktør
Jonoobi, MehdiOksman, Kristiina
Av organisasjonen
I samme tidsskrift
Industrial crops and products (Print)

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 50 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf