Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Experimental study on the effects of clearance and clamping in steel sheet metal shearing
Dalarna University, Borlänge.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Material- och solidmekanik.ORCID-id: 0000-0001-7074-8960
SSAB EMEA AB, SE-781 84 Borlänge.
2016 (engelsk)Inngår i: Journal of Materials Processing Technology, ISSN 0924-0136, E-ISSN 1873-4774, Vol. 229, s. 172-180Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Shear cutting is common within several sheet metal industry processing steps, e.g. in cut to length lines, slitting lines, end cropping. Shearing is fast and cheap relative to competing cutting methods like laser and plasma cutting, but involves large forces on the equipment that increase with increased sheet material strength. Accurate shear experiments are a prerequisite to increase the knowledge of shearing parameters, improve industrial shearing, and provide data for validation of numerical shear models. Here, the two shear parameters clearance and clamp configuration, identified as important to the shear results, were studied in an experimental set-up with well defined tool movement and high measurability of tool position and force. In addition to force measurements, the sheared edge geometry was characterized. Steels of low, medium, and high strength were selected for the study. Throughout the experimental study, the shear tool penetration before fracture decreased with increased material strength. The required shear force decreased and the force attempting to separate the two shear tools increased when one side of the sheet was left unclamped and free to move. Further, the maximum shear force increased with decreased clearance. Clearance changes were small and moreover continuously measured during all shear experiments.

sted, utgiver, år, opplag, sider
2016. Vol. 229, s. 172-180
HSV kategori
Forskningsprogram
Hållfasthetslära
Identifikatorer
URN: urn:nbn:se:ltu:diva-8674DOI: 10.1016/j.jmatprotec.2015.09.004ISI: 000367106000017Scopus ID: 2-s2.0-84942156277Lokal ID: 737ed041-de8c-40ed-b298-67e548cfdbeeOAI: oai:DiVA.org:ltu-8674DiVA, id: diva2:981612
Merknad
Validerad; 2015; Nivå 2; 20150907 (andbra)Tilgjengelig fra: 2016-09-29 Laget: 2016-09-29 Sist oppdatert: 2018-07-10bibliografisk kontrollert
Inngår i avhandling
1. Design and application of experimental methods for steel sheet shearing
Åpne denne publikasjonen i ny fane eller vindu >>Design and application of experimental methods for steel sheet shearing
2016 (engelsk)Doktoravhandling, med artikler (Annet vitenskapelig)
Alternativ tittel[sv]
Utveckling och tillämpning av experimentella metoder för klippning av stålplåt
Abstract [en]

Shearing is the process where sheet metal is mechanically cut between two tools. Various shearing technologies are commonly used in the sheet metal industry, for example, in cut to length lines, slitting lines, end cropping etc. Shearing has speed and cost advantages over competing cutting methods like laser and plasma cutting, but involves large forces on the equipment and large strains in the sheet material. The constant development of sheet metals toward higher strength and formability leads to increased forces on the shearing equipment and tools.

Shearing of new sheet materials imply new suitable shearing parameters. Investigations of the shearing parameters through live tests in the production are expensive and separate experiments are time consuming and requires specialized equipment. Studies involving a large number of parameters and coupled effects are therefore preferably performed by finite element based simulations. Accurate experimental data is still a prerequisite to validate such simulations. There is, however, a shortage of accurate experimental data to validate such simulations.

In industrial shearing processes, measured forces are always larger than the actual forces acting on the sheet, due to friction losses. Shearing also generates a force that attempts to separate the two tools with changed shearing conditions through increased clearance between the tools as result. Tool clearance is also the most common shearing parameter to adjust, depending on material grade and sheet thickness, to moderate the required force and to control the final sheared edge geometry.

In this work, an experimental procedure that provides a stable tool clearance together with accurate measurements of tool forces and tool displacements, was designed, built and evaluated. Important shearing parameters and demands on the experimental set-up were identified in a sensitivity analysis performed with finite element simulations under the assumption of plane strain. With respect to large tool clearance stability and accurate force measurements, a symmetric experiment with two simultaneous shears and internal balancing of forces attempting to separate the tools was constructed.

Steel sheets of different strength levels were sheared using the above mentioned experimental set-up, with various tool clearances, sheet clamping and rake angles. Results showed that tool penetration before fracture decreased with increased material strength. When one side of the sheet was left unclamped and free to move, the required shearing force decreased but instead the force attempting to separate the two tools increased. Further, the maximum shearing force decreased and the rollover increased with increased tool clearance.

Digital image correlation was applied to measure strains on the sheet surface. The obtained strain fields, together with a material model, were used to compute the stress state in the sheet. A comparison, up to crack initiation, of these experimental results with corresponding results from finite element simulations in three dimensions and at a plane strain approximation showed that effective strains on the surface are representative also for the bulk material.

A simple model was successfully applied to calculate the tool forces in shearing with angled tools from forces measured with parallel tools. These results suggest that, with respect to tool forces, a plane strain approximation is valid also at angled tools, at least for small rake angles.

In general terms, this study provide a stable symmetric experimental set-up with internal balancing of lateral forces, for accurate measurements of tool forces, tool displacements, and sheet deformations, to study the effects of important shearing parameters. The results give further insight to the strain and stress conditions at crack initiation during shearing, and can also be used to validate models of the shearing process.

sted, utgiver, år, opplag, sider
Luleå University of Technology, 2016
Serie
Doctoral thesis / Luleå University of Technology 1 jan 1997 → …, ISSN 1402-1544
HSV kategori
Forskningsprogram
Hållfasthetslära
Identifikatorer
urn:nbn:se:ltu:diva-59863 (URN)978-91-7583-733-8 (ISBN)978-91-7583-734-5 (ISBN)
Disputas
2016-12-20, E231, 09:00 (svensk)
Opponent
Veileder
Tilgjengelig fra: 2016-10-24 Laget: 2016-10-21 Sist oppdatert: 2017-11-24bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Personposter BETA

Oldenburg, Mats

Søk i DiVA

Av forfatter/redaktør
Oldenburg, Mats
Av organisasjonen
I samme tidsskrift
Journal of Materials Processing Technology

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 99 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf