Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Variables affecting stress development and resin conversion in light-cured dental composites
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Maskinelement.ORCID-id: 0000-0001-8676-8819
2004 (engelsk)Doktoravhandling, med artikler (Annet vitenskapelig)
Abstract [en]

The general aim of this dissertation was to identify and investigate factors that can be used to minimize stress development in light cured dental resins without compromising the conversion level of the polymer. Modulus of elasticity, polymerization contraction strain, degree of conversion and shrinkage of light-cure dental composites were determined after curing with three different light power densities where total irradiated energy (J/cm2) kept constant. FT-Raman spectroscopy was employed to determine the degree of conversion. The cure kinetic of light cured resins was studied by use of photocalorimetry (photo-DSC). Dynamic mechanical thermal (DMTA) analysis was used to investigate how different light curing methods affected glass transition and tangent delta of light curable dental resins when the temperature changed from 0 to 200°C. Optical properties of dental composites were studied. Three different filler types, two different surface treatments and eight different filler fractions per filler type and surface treatment were investigated. Light transmission was measured for the different composite compositions at sample thicknesses of 1 to 5 mm by use of a universal power meter. As long as the total light energy remained the same, the modulus of elasticity remained constant for each composite, even though the power density differed. Composite thickness, irradiance time, composition of the light cure composite and irradiation value had significant impact on degree of conversion. The irradiance value did not significantly affect on the transition temperature value. Initiator, co-initiators and light irradiance value had all significant impact on cure behavior. Different filler types and filler surface treatments had significant effects on light absorption. In general, light absorption increased linearly with filler fraction and sample thickness of the cured composites. Conclusion: Low rather than high light irradiance values decrease stress levels in composites, and comparable conversion levels are reached as long as the total light energy value remains the same for low versus high irradiance. By increasing the composite thickness above 2 mm but not exceeding 6 mm, energy levels exceeding 30 J are needed to achieve acceptable levels of degree of conversion. Different irradiance values do not affect the final Tg of tested composites as long as the total light energy remains the same. By using appropriate photo initiator/co-initiator combination and soft-start curing it is possible to achieve slow curing and high DC within a 40 s. As expected, different filler particle properties have significant effects on light absorption during curing making it important to consider these differences when one tries to develop a general light curing strategy for light curable dental resins.

sted, utgiver, år, opplag, sider
Luleå: Luleå tekniska universitet, 2004. , s. 160
Serie
Doctoral thesis / Luleå University of Technology 1 jan 1997 → …, ISSN 1402-1544 ; 2004:08
HSV kategori
Forskningsprogram
Maskinelement; Polymera konstruktionsmaterial
Identifikatorer
URN: urn:nbn:se:ltu:diva-26125Lokal ID: cc41a810-e80f-11db-b9a9-000ea68e967bOAI: oai:DiVA.org:ltu-26125DiVA, id: diva2:999284
Merknad
Godkänd; 2004; 20061030 (haneit)Tilgjengelig fra: 2016-09-30 Laget: 2016-09-30 Sist oppdatert: 2018-03-08bibliografisk kontrollert

Open Access i DiVA

fulltekst(54324 kB)6168 nedlastinger
Filinformasjon
Fil FULLTEXT01.pdfFilstørrelse 54324 kBChecksum SHA-512
df84b2afd081e47f76f8c01017c59ffd7b8cf757eafb10c1081a3c7a12a7435964e72a0af5db4c2dd5007c399cb9a0d33fef6359a72e80c9251e1b82e9f78c98
Type fulltextMimetype application/pdf

Person

Emami, Nazanin

Søk i DiVA

Av forfatter/redaktør
Emami, Nazanin
Av organisasjonen

Søk utenfor DiVA

GoogleGoogle Scholar
Totalt: 6168 nedlastinger
Antall nedlastinger er summen av alle nedlastinger av alle fulltekster. Det kan for eksempel være tidligere versjoner som er ikke lenger tilgjengelige

urn-nbn

Altmetric

urn-nbn
Totalt: 185 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf