Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
The Effects of Cutting Parameters and Tool Geometry on Cutting Forces and Tool Wear in Milling High-density Fiberboard with Ceramic Tools
Nanjing Forestry University.
Nanjing Forestry University.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknik.ORCID-id: 0000-0002-0145-080X
Nanjing Forestry University.
Visa övriga samt affilieringar
Antal upphovsmän: 62017 (Engelska)Ingår i: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 91, nr 9-12, s. 4033-4041Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

In this paper, the effects of cutting parametersand tool geometry on cutting forces and tool wear whenup-milling high-density fiberboard with alumina ceramiccutting tools were investigated. Under the condition ofthe same feed per tooth, average chip thickness, andclearance angle, the results shown are as follows: first,the tangential forces Ft and normal forces Fr at lowspeedcutting were higher than those at high-speed cutting,but increased slowly with the increase of cuttinglength and rake angle decrease. Second, increased cuttingspeed and decreased rake angle had a great effecton rake face wear. Third, the wear patterns of tool wearwere rake wear and flank wear, which included pull-outof grain, flaking, and chipping. The wear mechanismswere adhesive wear and abrasive wear. Finally, at lowspeedcutting, the cutting tools with bigger rake anglecan be selected to reduce the energy consumption ofmachine tools. The tools with smaller rake angle canbe used for high-speed cutting to improve tool lifeand productivity of processing.

Ort, förlag, år, upplaga, sidor
Springer, 2017. Vol. 91, nr 9-12, s. 4033-4041
Nyckelord [en]
Ceramic cutting tool, High-density fiberboard, Cutting forces, Tool wear
Nationell ämneskategori
Maskinteknik
Forskningsämne
Träteknik
Identifikatorer
URN: urn:nbn:se:ltu:diva-61890DOI: 10.1007/s00170-017-0085-8ISI: 000406976500092Scopus ID: 2-s2.0-85011650826OAI: oai:DiVA.org:ltu-61890DiVA, id: diva2:1073089
Anmärkning

Validerad;2017;Nivå 2;2017-08-16 (inah)

Tillgänglig från: 2017-02-09 Skapad: 2017-02-09 Senast uppdaterad: 2019-09-25Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Ekevad, Mats

Sök vidare i DiVA

Av författaren/redaktören
Ekevad, Mats
Av organisationen
Träteknik
I samma tidskrift
The International Journal of Advanced Manufacturing Technology
Maskinteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 192 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf