Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Laser Treatment as Sintering Process for Dispenser Printed Bismuth Telluride Based Paste
Additive Manufacturing and Printing, Fraunhofer-Institut für Werkstoff- und Strahltechnik, Dresden, Germany.
Additive Manufacturing and Printing, Fraunhofer-Institut für Werkstoff- und Strahltechnik, Dresden, Germany. Institute of Materials Science, Technische Universität Dresden, Dresden, Germany.
Additive Manufacturing and Printing, Fraunhofer-Institut für Werkstoff- und Strahltechnik, Dresden, Germany.
Additive Manufacturing and Printing, Fraunhofer-Institut für Werkstoff- und Strahltechnik, Dresden, Germany.
Visa övriga samt affilieringar
2019 (Engelska)Ingår i: Materials, ISSN 1996-1944, E-ISSN 1996-1944, Vol. 12, nr 20, artikel-id 3453Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Laser sintering as a thermal post treatment method for dispenser printed p- and n-type bismuth telluride based thermoelectric paste materials was investigated. A high-power fiber laser (600 W, 1064 nm) was used in combination with a scanning system to achieve high processing speed. A Design of Experiment (DoE) approach was used to identify the most relevant processing parameters. Printed layers were laser treated with different process parameters and the achieved sheet resistance, electrical conductivity, and Seebeck coefficient are compared to tube furnace processed reference specimen. For p-type material, electrical conductivity of 22 S/cm was achieved, compared to 15 S/cm in tube furnace process. For n-type material, conductivity achieved by laser process was much lower (7 S/cm) compared to 88 S/cm in furnace process. Also, Seebeck coefficient decreases during laser processing (40–70 µV/K and −110 µV/K) compared to the oven process (251 µV/K and −142 µV/K) for p- and n-type material. DoE did not yet deliver a set of optimum processing parameters, but supports doubts about the applicability of area specific laser energy density as a single parameter to optimize laser sintering process.

Ort, förlag, år, upplaga, sidor
MDPI, 2019. Vol. 12, nr 20, artikel-id 3453
Nyckelord [en]
laser sintering, thermoelectric, bismuth telluride, antimony telluride, design of experiment, additive manufacturing
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Forskningsämne
Produktionsutveckling
Identifikatorer
URN: urn:nbn:se:ltu:diva-77136DOI: 10.3390/ma12203453ISI: 000498402100174OAI: oai:DiVA.org:ltu-77136DiVA, id: diva2:1376949
Anmärkning

Validerad;2019;Nivå 2;2019-12-10 (johcin)

Tillgänglig från: 2019-12-10 Skapad: 2019-12-10 Senast uppdaterad: 2019-12-10Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Personposter BETA

Brückner, Frank

Sök vidare i DiVA

Av författaren/redaktören
Brückner, Frank
Av organisationen
Produkt- och produktionsutveckling
I samma tidskrift
Materials
Bearbetnings-, yt- och fogningsteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf