Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Influence of Electron Beam Powder Bed Fusion Process Parameters at Constant Volumetric Energy Density on Surface Topography and Microstructural Homogeneity of a Titanium Aluminide Alloy
Institute of Materials Science (IfWW), Technische Universität Dresden, 01069, Dresden, Germany; Fraunhofer Institute for Material and Beam Technology IWS, 01277, Dresden, Germany.ORCID-id: 0000-0002-3304-4283
Chair of Materials Test Engineering (WPT), TU Dortmund University, 44227, Dortmund, Germany.ORCID-id: 0000-0002-9960-735x
Institute of Materials Science (IfWW), Technische Universität Dresden, 01069, Dresden, Germany; Fraunhofer Institute for Material and Beam Technology IWS, 01277, Dresden, Germany.ORCID-id: 0000-0001-8126-8532
Fraunhofer Institute for Material and Beam Technology IWS, 01277, Dresden, Germany.ORCID-id: 0000-0003-1716-2156
Visa övriga samt affilieringar
2023 (Engelska)Ingår i: Advanced Engineering Materials, ISSN 1438-1656, E-ISSN 1527-2648, Vol. 25, nr 15, artikel-id 2201871Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

In powder bed fusion additive manufacturing, the volumetric energy density E V is a commonly used parameter to quantify process energy input. However, recent results question the suitability of E V as a design parameter, as varying the contributing parameters may yield different part properties. Herein, beam current, scan velocity, and line offset in electron beam powder bed fusion (PBF-EB) of the titanium aluminide alloy TNM–B1 are systematically varied while maintaining an overall constant E V. The samples are evaluated regarding surface morphology, relative density, microstructure, hardness, and aluminum loss due to evaporation. Moreover, the specimens are subjected to two different heat treatments to obtain fully lamellar (FL) and nearly lamellar (NLγ) microstructures, respectively. With a combination of low beam currents, low-to-intermediate scan velocities, and low line offsets, parts with even surfaces, relative densities above 99.9%, and homogeneous microstructures are achieved. On the other hand, especially high beam currents promote the formation of surface bulges and pronounced aluminum evaporation, resulting in inhomogeneous banded microstructures after heat treatment. The results demonstrate the importance of considering the individual parameters instead of E V in process optimization for PBF-EB.

Ort, förlag, år, upplaga, sidor
John Wiley & Sons, 2023. Vol. 25, nr 15, artikel-id 2201871
Nyckelord [en]
additive manufacturing, aluminum evaporation, electron beam powder bed fusion, heat treatments, process parameters, titanium aluminides
Nationell ämneskategori
Metallurgi och metalliska material
Forskningsämne
Produktionsutveckling
Identifikatorer
URN: urn:nbn:se:ltu:diva-97281DOI: 10.1002/adem.202201871ISI: 000976798900001Scopus ID: 2-s2.0-85151432356OAI: oai:DiVA.org:ltu-97281DiVA, id: diva2:1758694
Anmärkning

Godkänd;2023;Nivå 0;2023-08-15 (marisr);Konferensartikel i tidskrift

Special Issue: Structural Materials;

Funder: Deutsche Forschungsgemeinschaft, DFG (404665753, 406109547);

License fulltext: CC-BY. This is an open access article under the terms of the Creative Commons Attribution License, which permits use, distribution and reproduction in any medium, provided the original work is properly cited.

Tillgänglig från: 2023-05-23 Skapad: 2023-05-23 Senast uppdaterad: 2023-08-15Bibliografiskt granskad

Open Access i DiVA

fulltext(5842 kB)123 nedladdningar
Filinformation
Filnamn FULLTEXT02.pdfFilstorlek 5842 kBChecksumma SHA-512
bfc7800566d9acd07b6e04522153bfaed0aeebc88cac90d8ae7a2285aaaf580571d80fdf59c25735bee544afec4cb9a9160ffb1d394b6e6229d6bb2ab1759073
Typ fulltextMimetyp application/pdf

Övriga länkar

Förlagets fulltextScopus

Person

Brueckner, Frank

Sök vidare i DiVA

Av författaren/redaktören
Moritz, JulianeTeschke, MirkoMarquardt, AxelStepien, LukasBrueckner, FrankWalther, FrankLeyens, Christoph
Av organisationen
Produkt- och produktionsutveckling
I samma tidskrift
Advanced Engineering Materials
Metallurgi och metalliska material

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 152 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 183 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf