Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
The significance of oil thermal properties on the performance of a tilting-pad thrust bearing
Laboratory of Solid Mechanics, University of Poitiers.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Maskinelement.ORCID-id: 0000-0001-9110-2819
2002 (Engelska)Ingår i: Journal of tribology, ISSN 0742-4787, E-ISSN 1528-8897, Vol. 124, nr 2, s. 377-385Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

This paper is a report into an experimental and theoretical investigation of the effect of oil thermal properties on the performance of a tilting-pad thrust bearing. Three oils, namely poly-α-olefin, ester and mineral base, were chosen for this study. These oils all have same viscosity grade (ISO VG46) but differ in their rates of viscosity variation with temperature and in their heat capacity and thermal conductivity values. Mineral base oil of a higher viscosity grade (ISO VG68) was also analyzed for comparison. Experimental data were obtained from an equalizing tilting-pad thrust bearing with an outer diameter of 228.6 mm operating in a flooded lubrication mode. Simultaneous measurements of pad and collar temperatures, friction torque, pressures and oil film thickness were taken. In the tests, oil supply temperature and flow rate were held constant for all load-speed combinations. The theoretical analysis of oil performance was based on a three-dimensional TEHD model. In the analysis, thermal effects were locally taken into account and heat transfer into the pads was considered. The displacements of the active surface of the pads, due to pressure and temperature fields, were determined. The effect of initial pad crowning on the oil film thickness is discussed. Experimental and theoretical results are compared and analyzed in terms of the inlet and outlet oil film thickness, bearing operating temperature and power loss.

Ort, förlag, år, upplaga, sidor
2002. Vol. 124, nr 2, s. 377-385
Nationell ämneskategori
Tribologi (ytteknik omfattande friktion, nötning och smörjning)
Forskningsämne
Maskinelement
Identifikatorer
URN: urn:nbn:se:ltu:diva-2868DOI: 10.1115/1.1405129ISI: 000175335600019Scopus ID: 2-s2.0-0036525770Lokalt ID: 09612f40-c25e-11db-9ea3-000ea68e967bOAI: oai:DiVA.org:ltu-2868DiVA, id: diva2:975722
Anmärkning
Validerad; 2002; 20061109 (cira)Tillgänglig från: 2016-09-29 Skapad: 2016-09-29 Senast uppdaterad: 2018-07-10Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Glavatskikh, SergeiLarsson, Roland

Sök vidare i DiVA

Av författaren/redaktören
Glavatskikh, SergeiLarsson, Roland
Av organisationen
Maskinelement
I samma tidskrift
Journal of tribology
Tribologi (ytteknik omfattande friktion, nötning och smörjning)

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 42 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf