Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Nanoindentation and fracture toughness of nanostructured zirconia/multi-walled carbon nanotube composites
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Materialvetenskap.
Department of Materials Science and Engineering, Universitat Politècnica de Catalunya, Barcelona.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Materialvetenskap.ORCID-id: 0000-0003-3661-9262
Department of Materials Science and Engineering, Universitat Politècnica de Catalunya, Barcelona.
Visa övriga samt affilieringar
2015 (Engelska)Ingår i: Ceramics International, ISSN 0272-8842, E-ISSN 1873-3956, Vol. 41, nr 2, s. 2453-2461Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Multi-walled carbon nanotubes (MWCNTs)/3 mol% yttria-doped tetragonal zirconia (3Y-TZP) composites were produced using spark plasma sintering (SPS) with MWCNT content ranging within 0-2 wt%. In the present paper, it was shown that the addition of MWCNTs results in a refinement of the composites microstructure. Moreover, nanoindentation tests were performed in order to monitor the change in elastic modulus and hardness with MWCNT content and it was found that both properties decrease with the addition of MWCNT content. A novel method was used to measure the true fracture toughness of the composites by producing a shallow surface sharp notch machined by ultra-short pulsed laser ablation on the surface of beam specimens. The true fracture toughness obtained on this laser machined single edge V-notch beam (SEVNB) specimens tested in four point bending was compared to the indentation fracture toughness measured using a Vickers indenter. It was found that the indentation fracture toughness increases with increasing MWCNT content, while the true fracture toughness determined with SEVNB was practically independent of the composition. Finally, it was concluded that the increase in the resistance to indentation cracking of the composites with respect to 3Y-TZP matrix cannot be associated to higher true fracture toughness. The results were discussed in terms of transformation toughening, damage induced in front of the notch tip, microstructure of the composites, and fracture toughness of 3Y-TZP.

Ort, förlag, år, upplaga, sidor
2015. Vol. 41, nr 2, s. 2453-2461
Nationell ämneskategori
Annan materialteknik
Forskningsämne
Materialteknik
Identifikatorer
URN: urn:nbn:se:ltu:diva-7562DOI: 10.1016/j.ceramint.2014.10.060ISI: 000348961400067Scopus ID: 2-s2.0-84919427557Lokalt ID: 5f26f0e1-51b9-4553-ab72-ea559a3acbc8OAI: oai:DiVA.org:ltu-7562DiVA, id: diva2:980452
Anmärkning
Validerad; 2015; Nivå 2; 20141021 (andbra)Tillgänglig från: 2016-09-29 Skapad: 2016-09-29 Senast uppdaterad: 2018-07-10Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Melk, LatifaAntti, Marta-Lena

Sök vidare i DiVA

Av författaren/redaktören
Melk, LatifaAntti, Marta-Lena
Av organisationen
Materialvetenskap
I samma tidskrift
Ceramics International
Annan materialteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 257 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf