Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Effect of adding a type of binder phase on the microstructure, properties and heat treatment of steel bonded TiC cermets
Institute of Powder Metallurgy, School of Materials Science and Engineering, University of Science and Technology, Beijing.ORCID-id: 0000-0003-4888-6237
Institute of Powder Metallurgy, School of Materials Science and Engineering, University of Science and Technology, Beijing.
Department of Metallurgical and Materials Engineering, University of Engineering and Technology, Lahore.
Institute of Powder Metallurgy, School of Materials Science and Engineering, University of Science and Technology, Beijing.
2007 (Engelska)Ingår i: Progress in powder metallurgy: proceedings of the 2006 Powder Metallurgy World Congress & Exhibition (PM 2006), held in Busan Exhibition & Convention Center (BEXCO), Busan, Korea, September 24 - 28, 2006 / [ed] Duk Yong Yoon; Suk-Joong L. Kang; Kwang Yong Eun; Yong-Seog Kim, Uetikon-Zürich: Trans Tech Publications Inc., 2007, Vol. 534-536, s. 1161-1164Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

Particulate TiC reinforced 465 maraging stainless steel matrix Cermets were processed by conventional P/M. The binder phase was added in the form of elemental powders and master alloy powders. The microstructures, binder phase variation with TiC content and mechanical properties were evaluated. The addition of a type of binder phase largely effects the microstructure and mechanical properties. When a master alloy binder phase was used the microstructure showed interphase debondings, microcracks and large growths of TiC particles. Where as, elemental powders in the composition of binder phases showed defect free microstructure of steel bonded cermets. The binder phase variation from starting composition was observed with increase in wt% TiC content and this variation was higher when the master alloy powders were used as a binder. After heat treatment and aging, an increase in hardness was observed. The increase in hardness was attributed to the aging reaction in maraging stainless steel. The response to heat treatment was decreased with an increase in TiC content due to the shift of binder phase from the starting composition.

Ort, förlag, år, upplaga, sidor
Uetikon-Zürich: Trans Tech Publications Inc., 2007. Vol. 534-536, s. 1161-1164
Serie
Materials Science Forum, ISSN 0255-5476
Nationell ämneskategori
Annan materialteknik
Forskningsämne
Materialteknik
Identifikatorer
URN: urn:nbn:se:ltu:diva-30783DOI: 10.4028/www.scientific.net/MSF.534-536.1161Lokalt ID: 4b83cb3e-38c9-448c-bc99-5c2018b40ef4OAI: oai:DiVA.org:ltu-30783DiVA, id: diva2:1004012
Konferens
Powder Metallurgy World Congress & Exhibition : 24/08/2006 - 28/08/2006
Anmärkning
Upprättat; 2007; 20150416 (farakh)Tillgänglig från: 2016-09-30 Skapad: 2016-09-30 Senast uppdaterad: 2017-11-25Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Personposter BETA

Akhtar, Farid

Sök vidare i DiVA

Av författaren/redaktören
Akhtar, Farid
Annan materialteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 112 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf