Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Lateral cutting forces for different tooth geometries and cutting directions
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknologi.ORCID-id: 0000-0002-0145-080X
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknologi.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknologi.
2012 (engelsk)Inngår i: Wood Material Science & Engineering, ISSN 1748-0272, E-ISSN 1748-0280, Vol. 7, nr 3, s. 126-133Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Lateral (sideways) cutting forces were measured for 6 different tooth geometries when cutting green spruce and pine heartwood. The teeth were intended for use on circular saw blades for the rip sawing of logs. The 6 tooth geometries were designated straight, pointed, bevelled, rounded, trapezoidal and hollowed out. Cutting speed was 15 m/s, feed per tooth was 0.3 mm and the cutting directions were 90°–90° (rip sawing) and 90°–0° (milling), with two different variants of growth ring angles for each direction. The tools were tested in sharp conditions, in dull conditions and in a dull condition with a corner broken off. All lateral forces were small when cutting with sharp teeth, except for the rounded and bevelled teeth. Lateral forces increased with wear, except for a period of initial wear where the lateral forces were reduced. High wear resulted in greater lateral forces, most probably due to unsymmetrical wear. Growth ring direction did not generally affect lateral forces. The teeth with acute corners, which were the straight and hollowed out tooth, were most sensitive to a broken off corner. The lateral forces in the cases of wood cutting at 90°–90° increased less with wear compared to the 90°–0° cases.

sted, utgiver, år, opplag, sider
2012. Vol. 7, nr 3, s. 126-133
HSV kategori
Forskningsprogram
Träteknik
Identifikatorer
URN: urn:nbn:se:ltu:diva-32650DOI: 10.1080/17480272.2012.662699Scopus ID: 2-s2.0-84866855032Lokal ID: 734f1613-7514-4d5d-9393-8de34d000886OAI: oai:DiVA.org:ltu-32650DiVA, id: diva2:1005884
Konferanse
International Wood Machining Seminar : 07/06/2011 - 10/06/2011
Merknad
Validerad; 2012; 20120607 (matse); Konferensartikel i tidskriftTilgjengelig fra: 2016-09-30 Laget: 2016-09-30 Sist oppdatert: 2018-07-10bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Person

Ekevad, MatsCristovao, LuisMarklund, Birger

Søk i DiVA

Av forfatter/redaktør
Ekevad, MatsCristovao, LuisMarklund, Birger
Av organisasjonen
I samme tidsskrift
Wood Material Science & Engineering

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 224 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf