Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Qualitative statistical analysis of simulated data from a pilot scale mill
Luleå tekniska universitet, Institutionen för samhällsbyggnad och naturresurser, Industriell miljö- och processteknik.ORCID-id: 0000-0002-8032-9388
2011 (Engelska)Ingår i: Particle-based Methods - Fundamentals and Applications / [ed] Eugenio Oñate; D.R.J. Owen, Barcelona: International Center for Numerical Methods in Engineering (CIMNE), 2011, s. 43-51Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

Grinding is the process of reducing a particle size distribution of an extracted ore and is commonly performed in a tumbling mill. It is a complex procedure and there is a lack of knowledge of what really happens inside the mill. A number of pilot-scale experiments were done at LKAB's pilot plant at Malmberget, Sweden [1]. In this particular pilot mill, a continuous charge measurement system is installed in one of the lifters and it gives a deflection signal produced by the mill charge. From this signal it is possible to detect features correlated to the settings of the mill. Large, real experiments are very difficult to control and are of course, very costly and time consuming. A 10 cm slice of the mill was simulated with discrete element method (DEM) for different mill operating conditions. From the simulations a deflection signal was extracted and validated against real data. There is a difference in the signal, mainly due to the lack of slurry in the simulations, but the behaviour when the mills operating conditions changes seems to be the same in both the simulated and the measured signals. To analyse the data from the simulation a statistical analysis on a full factorial design was done. Two levels of degree of filling of the mill, two different rotational speeds, two levels of friction and different types of particles were selected as factors. The response data are two angles: toe and shoulder angle. The toe angle is when the lifter hits the charge and the shoulder angle is when the lifter leaves the charge. The analysis show that the toe angle increases when the degree of filling is low and the rotational speed is high. It is also clear that the particle shape influences the charge behaviour. The simulated changes correspond to changes detected in pilot mill runs. This is important since it validates the DEM model. In essence, mill simulations are easily done and the changes of factor levels cause the simulated mill to react in similar manner as in real cases. One advantage is that in simulations one factor can be isolated and changed while the others are kept at constant values, which in turn creates the possibility to investigate one factor at a time. In real experiments, the factors are more dependent on each other and there is a very high disturbance from noise.

Ort, förlag, år, upplaga, sidor
Barcelona: International Center for Numerical Methods in Engineering (CIMNE), 2011. s. 43-51
Nationell ämneskategori
Metallurgi och metalliska material
Forskningsämne
Mineralteknik
Identifikatorer
URN: urn:nbn:se:ltu:diva-34712Lokalt ID: 8fc632da-90d8-428a-aba9-2d790f9cad22ISBN: 978-848992567-0 (tryckt)OAI: oai:DiVA.org:ltu-34712DiVA, id: diva2:1007963
Konferens
International Conference on Particle-Based Methods : fundamentals and applications 26/10/2011 - 28/10/2011
Anmärkning
Godkänd; 2011; 20111229 (palle)Tillgänglig från: 2016-09-30 Skapad: 2016-09-30 Senast uppdaterad: 2023-09-06Bibliografiskt granskad

Open Access i DiVA

fulltext(277 kB)134 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 277 kBChecksumma SHA-512
0337a14b5505ffbebd0670107a09c034a8273985789631358cbaf81dccf9fcc032bec228d8891f5fbc13365ef20e9b689314bc36bf1fa7a70a78ca117947ce0d
Typ fulltextMimetyp application/pdf

Person

Alatalo, JohannaPålsson, Bertil

Sök vidare i DiVA

Av författaren/redaktören
Alatalo, JohannaPålsson, Bertil
Av organisationen
Industriell miljö- och processteknik
Metallurgi och metalliska material

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 134 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

isbn
urn-nbn

Altmetricpoäng

isbn
urn-nbn
Totalt: 440 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf