Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Comparison of Three Different Arc Modes When Laser-arc Hybrid Welding in Steel
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Produkt- och produktionsutveckling.ORCID-id: 0000-0003-4265-1541
2015 (Engelska)Ingår i: ILSC 2015 Conference Program and Proceeding, Laser Institute of America , 2015Konferensbidrag, Publicerat paper (Refereegranskat)
Abstract [en]

Traditionally, Laser Arc-Hybrid Welding (LAHW) is made using a Gas Metal Arc (GMA) heat source in pulsed mode. In this study, welds made with three different arc modes under various conditions are compared. The arc modes compared for LAHW are; Standard, Pulsed and Cold Metal Transfer (CMT). The pulsed mode, using power modulation, is more controlled than the “natural” Standard mode and offers globular drop transfer with reduced heat input to the work piece, enabling thinner materials to be welded. The CMT arc mode also uses power modulation as well as controlled wire feeding. This enables surface tension drop transfer, involving even less heat input and is also considered to generate less undercuts and spatter than the other two arc modes.The welds compared were made in 7 mm thick S420 laser cut steel sheets with two different welding speeds and gap sizes. They were made using close-to-production setup within the limitations of the CMT capabilities, i.e. low and medium wire feed rates. The weld caps and roots were studied optically and the structures were analyzed by making cross-sectional macrographs longitudinally and transversally. These cross sections were analyzed geometrically, structurally and also hardness tested. The welds were also studied and analyzed by means of pre- and post-weld scanning as well as High Speed Imaging (HSI).The study shows that the laser keyhole reduces the effect of the arc modes, enabling higher welding speeds than without the laser. The gouge formed in front of the keyhole determines occurrence of undercuts and bead uniformity. The material mixing of filler and base material, and laser penetration spiking, is also influenced by the depth of the arc gouge. The material structure is also affected to some degrees for expected performances. Even though the short-arc technique CMT show promising results, the pros and cons for each arc technique are discussed.

Ort, förlag, år, upplaga, sidor
Laser Institute of America , 2015.
Nationell ämneskategori
Bearbetnings-, yt- och fogningsteknik
Forskningsämne
Produktionsutveckling
Identifikatorer
URN: urn:nbn:se:ltu:diva-39081Lokalt ID: db06f81e-d597-44d4-af90-e8aa35316c68ISBN: 978-1-940168-05-0 (tryckt)OAI: oai:DiVA.org:ltu-39081DiVA, id: diva2:1012589
Konferens
International Congress on Applications of Lasers & Electro-Optics : 19/10/2015 - 22/10/2015
Anmärkning

För godkännande; 2015; 20151127 (jankar)

Tillgänglig från: 2016-10-03 Skapad: 2016-10-03 Senast uppdaterad: 2017-11-25Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Person

Frostevarg, Jan

Sök vidare i DiVA

Av författaren/redaktören
Frostevarg, Jan
Av organisationen
Produkt- och produktionsutveckling
Bearbetnings-, yt- och fogningsteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

isbn
urn-nbn

Altmetricpoäng

isbn
urn-nbn
Totalt: 82 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf