Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Modeling and pilot plant runs of slow biomass pyrolysis in a rotary kiln
Department Chemical Engineering and Technology, KTH Royal Institute of Technology.
Luleå University of Technology, Department of Engineering Sciences and Mathematics, Energy Science.
Cortus Energy AB.
Cortus Energy AB.
Show others and affiliations
2017 (English)In: Applied Energy, ISSN 0306-2619, E-ISSN 1872-9118, Vol. 207, p. 123-133Article in journal (Refereed) Published
Abstract [en]

Pyrolysis of biomass in a rotary kiln finds application both as an intermediate step in multistage gasification as well as a process on its own for the production of biochar. In this work, a numerical model for pyrolysis of lignocellulosic biomass in a rotary kiln is developed. The model is based on a set of conservation equations for mass and energy, combined with independent submodels for the pyrolysis reaction, heat transfer, and granular flow inside the kiln. The pyrolysis reaction is described by a two-step mechanism where biomass decays into gas, char, and tar that subsequently undergo further reactions; the heat transfer model accounts for conduction, convection and radiation inside the kiln; and the granular flow model is described by the well known Saeman model. The model is compared to experimental data obtained from a pilot scale rotary kiln pyrolyzer. In total 9 pilot plant trials at different feed flow rate and different heat supply were run. For moderate heat supplies we found good agreement between the model and the experiments while deviations were seen at high heat supply. Using the model to simulate various operation conditions reveals a strong interplay between heat transfer and granular flow which both are controlled by the kiln rotation speed. Also, the model indicates the importance of heat losses and lays the foundation for scale up calculations and process optimization.

Place, publisher, year, edition, pages
Elsevier, 2017. Vol. 207, p. 123-133
National Category
Energy Engineering
Research subject
Energy Engineering
Identifiers
URN: urn:nbn:se:ltu:diva-64494DOI: 10.1016/j.apenergy.2017.06.034ISI: 000417229300012OAI: oai:DiVA.org:ltu-64494DiVA, id: diva2:1115037
Conference
8th International Conference on Applied Energy (ICAE2016), Bejing, Oct 8-11, 2016
Note

Konferensartikel i tidskrift

Available from: 2017-06-26 Created: 2017-06-26 Last updated: 2018-10-24Bibliographically approved
In thesis
1. Biocarbon for fossil coal replacement
Open this publication in new window or tab >>Biocarbon for fossil coal replacement
2018 (English)Licentiate thesis, comprehensive summary (Other academic)
Alternative title[sv]
Biokol for ersättning av fossil kol
Abstract [en]

This research aims to provide a full view of knowledge in charcoal production for fossil coal replacement. Charcoal from biomass is a promising material to replace fossil coal, which is using as heating source or reactant in the industrial sector. Nowadays, charcoal with quality comparable to fossil coal is produced by high-temperature pyrolysis, but efficiency of the production is relatively low due to the trade-off between charcoal property and yield by pyrolysis temperature. Increasing charcoal yield by means of secondary char formation in pyrolysis of large wood particles is the primary method considering in this work. This research has explored increasing efficiency of charcoal production by bio-oil recycling and CO2 purging. These proposed techniques significantly increase concentration and extend residence time of volatiles inside particle of woodchip resulting extra charcoal. Characterization of charcoals implies negligible effect of these methods on charcoal properties such as elemental composition, heating value, morphological structure, and chemical structure. Besides, reactivity of charcoal slightly increased when these methods were applied. A numerical model of pyrolysis in a rotary kiln reactor has been developed to study the effect of design parameters and conditions in reactor scale. The simulation results showed fair prediction of temperature profiles and products distribution along the reactor length. Nonetheless, to deliver full knowledge in charcoal production, further works are planned to be done at the end of this doctoral research.

Place, publisher, year, edition, pages
Luleå: Luleå University of Technology, 2018
Series
Licentiate thesis / Luleå University of Technology, ISSN 1402-1757
Keywords
Biomass pyrolysis, charcoal, bio-oil recycling, CO2 utilization, reactivity, rotary drum
National Category
Energy Engineering Chemical Engineering Engineering and Technology
Research subject
Energy Engineering
Identifiers
urn:nbn:se:ltu:diva-71324 (URN)978-91-7790-242-3 (ISBN)978-91-7790-243-0 (ISBN)
Presentation
2018-12-11, Lueå University of Technology, Luleå, 10:56 (English)
Opponent
Supervisors
Available from: 2018-10-25 Created: 2018-10-24 Last updated: 2019-04-03Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full text

Authority records BETA

Phounglamcheik, Aekjuthon

Search in DiVA

By author/editor
Phounglamcheik, Aekjuthon
By organisation
Energy Science
In the same journal
Applied Energy
Energy Engineering

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 230 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf