Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Production and In-Plane Compression Mechanics of Alternatively Angled Layered Cross-Laminated Timber
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknik.ORCID-id: 0000-0001-7091-6696
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknik.ORCID-id: 0000-0001-8404-7356
2018 (Engelska)Ingår i: BioResources, ISSN 1930-2126, E-ISSN 1930-2126, Vol. 13, nr 2, s. 4029-4045Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Increasing awareness of sustainable building materials has led to interest in enhancing the structural performance of engineered wood products. This paper reports mechanical properties of cross-laminated timber (CLT) panels constructed with layers angled in an alternative configuration on a modified industrial CLT production line. Timber lamellae were adhesively bonded together in a single-step press procedure to form CLT panels. Transverse layers were laid at an angle of 45°, instead of the conventional 90° angle with respect to the longitudinal layers’ 0° angle. Tests were carried out on 20 five-layered CLT panels divided into two matched groups with either a 45° or a 90° configuration; an in-plane uniaxial compressive loading was applied in the principal orientation of the panels. These tests showed that the 45°-configured panels had a 30% higher compression stiffness and a 15% higher compression strength than the 90° configuration. The results also revealed that the 45°-configured CLT can be industrially produced without using more material than is required for conventional CLT 90° panels. In addition, the design possibility that the 45°-configured CLT can carry a given load while using less material also suggests that it is possible to use CLT in a wider range of structural applications.

Ort, förlag, år, upplaga, sidor
University of North Carolina Press, 2018. Vol. 13, nr 2, s. 4029-4045
Nyckelord [en]
CLT manufacturing, Crosslam, Cross-ply, Diagonal-laminated lumber, Impact of laminate orientation, In-plane rotation, Grain inclination angle, Mass timber engineering, Solid wood panel, X-lam
Nationell ämneskategori
Husbyggnad Annan maskinteknik
Forskningsämne
Träteknik
Identifikatorer
URN: urn:nbn:se:ltu:diva-68424DOI: 10.15376/biores.13.2.4029-4045ISI: 000440518000021OAI: oai:DiVA.org:ltu-68424DiVA, id: diva2:1199291
Anmärkning

Validerad;2018;Nivå 2;2018-04-26 (andbra)

Tillgänglig från: 2018-04-20 Skapad: 2018-04-20 Senast uppdaterad: 2019-01-15Bibliografiskt granskad
Ingår i avhandling
1. Mechanics of Cross-Laminated Timber
Öppna denna publikation i ny flik eller fönster >>Mechanics of Cross-Laminated Timber
2018 (Engelska)Licentiatavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

Increasing awareness of sustainable building materials has led to interest in enhancing the structural performance of engineered wood products. Wood is a sustainable, renewable material, and the increasing use of wood in construction contributes to its sustainability. Multi-layer wooden panels are one type of engineered wood product used in construction.

There are various techniques to assemble multi-layer wooden panels into prefabricated, load-bearing construction elements. Assembly techniques considered in the earliest stages of this research work were laminating, nailing, stapling, screwing, stress laminating, doweling, dovetailing, and wood welding. Cross-laminated timber (CLT) was found to offer some advantages over these other techniques. It is cost-effective, not patented, offers freedom of choice regarding the visibility of surfaces, provides the possibility of using different timber quality in the same panel at different points of its thickness, and is the most well-established assembly technique currently used in the industrial market.

Building upon that foundational work, the operational capabilities of CLT were further evaluated by creating panels with different layer orientations. The mechanical properties of CLT panels constructed with layers angled in an alternative configuration produced on a modified industrial CLT production line were evaluated. Timber lamellae were adhesively bonded in a single-step press procedure to form CLT panels. Transverse layers were laid at a 45° angle instead of the conventional 90° angle with respect to the longitudinal layers’ 0° angle.

Tests were carried out on 40 five-layered CLT panels, each with either a ±45° or a 90° configuration. Half of these panels were evaluated under bending: out-of-plane loading was applied in the principal orientation of the panels via four-point bending. The other twenty were evaluated under compression: an in-plane uniaxial compressive loading was applied in the principal orientation of the panels. Quasi-static loading conditions were used for both in- and out-of-plane testing to determine the extent to which the load-bearing capacity of such panels could be enhanced under the current load case. Modified CLT showed higher stiffness, strength, and fifth-percentile characteristics, values that indicate the load-bearing capacity of these panels as a construction material. Failure modes under in- and out-of-plane loading for each panel type were also assessed.

Data from out-of-plane loading were further analysed. A non-contact full-field measurement and analysis technique based on digital image correlation (DIC) was utilised for analysis at global and local scales. DIC evaluation of 100 CLT layers showed that a considerable part of the stiffness of conventional CLT is reduced by the shear resistance of its transverse layers. The presence of heterogeneous features, such as knots, has the desirable effect of reducing the propagation of shear fraction along the layers. These results call into question the current grading criteria in the CLT standard. It is suggested that the lower timber grading limit be adjusted for increased value-yield.

The overall experimental results suggest the use of CLT panels with a ±45°-layered configuration for construction. They also motivate the use of alternatively angled layered panels for more construction design freedom, especially in areas that demand shear resistance. In addition, the design possibility that such 45°-configured CLT can carry a given load while using less material than conventional CLT suggests the potential to use such panels in a wider range of structural applications. The results of test production revealed that 45°-configured CLT can be industrially produced without using more material than is required for construction of conventional 90°-configured panels. Based on these results, CLT should be further explored as a suitable product for use in more wooden-panel construction.

Ort, förlag, år, upplaga, sidor
Luleå: Luleå University of Technology, 2018
Serie
Licentiate thesis / Luleå University of Technology, ISSN 1402-1757
Nyckelord
CLT assembly, CLT manufacture, Crosslam, DIC analysis, Digital speckle photography, Full-field mechanics, Laminated wood product, Mass timber engineering, Non-contact measurement, Non-destructive, Optical measurement, Panel configuration, Strain localization, X-lam, Alternativ byggmetod, Bildkorrelation, Hållbart byggande, KL- trä, Korslimmat trä, Skjuvtöjning, Massivträ, Träkonstruktion
Nationell ämneskategori
Maskinteknik Annan maskinteknik
Forskningsämne
Träteknik
Identifikatorer
urn:nbn:se:ltu:diva-68729 (URN)978-91-7790-150-1 (ISBN)978-91-7790-151-8 (ISBN)
Presentation
2018-06-20, Hörsal A, Luleå tekniska universitet, Skellefteå, 10:00 (Engelska)
Opponent
Handledare
Anmärkning

External cooperation: Martinson Group AB and Research Institutes of Sweden (RISE)

Tillgänglig från: 2018-05-15 Skapad: 2018-05-15 Senast uppdaterad: 2018-06-13Bibliografiskt granskad

Open Access i DiVA

fulltext(1276 kB)65 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 1276 kBChecksumma SHA-512
910beb52b44912b38d04ee44cb2f254c41d76ef88acd90d20fd0e4ac73d058b36d652fa32eab695a12b47e21ddb76b1bb2164cc7df406ec9b18643dccb5a2095
Typ fulltextMimetyp application/pdf

Övriga länkar

Förlagets fulltext

Personposter BETA

Buck, DietrichHagman, Olle

Sök vidare i DiVA

Av författaren/redaktören
Buck, DietrichHagman, Olle
Av organisationen
Träteknik
I samma tidskrift
BioResources
HusbyggnadAnnan maskinteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 65 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 229 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf