Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Numerical investigation of galling in a press hardening experiment with AlSi-coated workpieces
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Material- och solidmekanik.ORCID-id: 0000-0002-9421-6587
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Maskinelement.ORCID-id: 0000-0003-3123-0303
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Maskinelement.ORCID-id: 0000-0003-1162-4671
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Maskinelement.ORCID-id: 0000-0003-1454-1118
Visa övriga samt affilieringar
2019 (Engelska)Ingår i: Engineering Failure Analysis, ISSN 1350-6307, E-ISSN 1873-1961, Vol. 99, s. 85-96Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Press hardened steels are commonly used as a lightweight choice for manufacturing car components because of the high ratio of strength to weight. The use of ultra-high-strength steels for the design of lightweight vehicles contributes to the reduction of emissions of carbon dioxide while maintaining passenger safety. Stamping tools used in press hardening processes suffer harsh contact conditionsin terms of dramatic temperature changes, cyclic loadings, and complex interactions between coatings and oxidation. In mass production, tool wear is an inevitable problem that increases maintenance costs. Severe adhesive wear, also called galling, substantially occurs in the stamping tool used against Al—Si-coated workpieces. The galling that takes place during press hardening not only degrades the production quality but also shortens the service life of the tool. In order to properly arrange tool maintenance and minimize galling through adjusting process parameters, engineers need to know when and where galling occurs, based on modelling of the galling in press hardening simulations. In order to implement a galling simulation for press hardening, a modified Archard wear model is employed in the present study, which is a contact-mechanics-based model. The specific wear rate in the model is calibrated by the quantitative galling measurements of a high-temperature tribometer test. The tribological test is designed to mimic the press hardening conditions, where the correlations between galling and process parameters such as temperature, pressure, and sliding distance are outlined. The galling simulation is implemented in a full-scale press hardening experiment, and the predicted galling is validated in terms of severe galling positions and galling profiles. The galling profile evolution is correlated to variations in the contact conditions. Uncertainties in the numerical model, such as the choice of penalty scaling factor and friction coefficient, are analysed with a parameter study and discussed. This study demonstrates finite element (FE) simulations involving galling prediction in press hardening so as to improve product development and production efficiency.

Ort, förlag, år, upplaga, sidor
Elsevier, 2019. Vol. 99, s. 85-96
Nyckelord [en]
Contact conditions, High-temperature tribometer, FE simulation, Galling prediction
Nationell ämneskategori
Teknisk mekanik Tribologi (ytteknik omfattande friktion, nötning och smörjning)
Forskningsämne
Hållfasthetslära; Maskinelement
Identifikatorer
URN: urn:nbn:se:ltu:diva-73044DOI: 10.1016/j.engfailanal.2019.01.059ISI: 000464957800008Scopus ID: 2-s2.0-85061604416OAI: oai:DiVA.org:ltu-73044DiVA, id: diva2:1292247
Anmärkning

Validerad;2019;Nivå 2;2019-02-27 (johcin)

Tillgänglig från: 2019-02-27 Skapad: 2019-02-27 Senast uppdaterad: 2019-05-02Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Deng, LiangPelcastre, LeonardoHardell, JensPrakash, BrahamOldenburg, Mats

Sök vidare i DiVA

Av författaren/redaktören
Deng, LiangPelcastre, LeonardoHardell, JensPrakash, BrahamOldenburg, Mats
Av organisationen
Material- och solidmekanikMaskinelement
I samma tidskrift
Engineering Failure Analysis
Teknisk mekanikTribologi (ytteknik omfattande friktion, nötning och smörjning)

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 85 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf