Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Finite element analysis of bending stiffness for cross-laminated timber with varying board width
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknik.ORCID-id: 0000-0002-4686-4010
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknik.ORCID-id: 0000-0002-0900-5110
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknik.ORCID-id: 0000-0002-0145-080x
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknik.ORCID-id: 0000-0001-9196-0370
2019 (Engelska)Ingår i: Wood Material Science & Engineering, ISSN 1748-0272, E-ISSN 1748-0280, Vol. 14, nr 6, s. 392-403Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

ross laminated timber (CLT) is a wood panelling building system that is used in construction, e.g. for floors, walls and beams. Because of the increased use of CLT, it is important to have accurate simulation models. CLT systems are simulated with one-dimensional and two-dimensional (2D) methods because they are fast and deliver practical results. However, because non-edge-glued panels cannot be modelled under 2D, these results may differ from more accurate calculations in three dimensions (3D). In this investigation, CLT panels with different width-to-thickness ratios for the boards have been simulated using the finite element method. The size of the CLT-panels was 3.0 m × 3.9 m and they had three and five laminate layers oriented 0°–90°–0° and 0°–90°–0°–90°–0°. The thicknesses of the boards were 33.33, 40.0, and 46.5 mm. The CLT panel deformation was compared by using a distributed out-of-plane load. Results showed that panels with narrow boards were less stiff than wide boards for the four-sided support setup. The results also showed that 2D models underestimate the displacement when compared to 3D models. By adjusting the stiffness factor k88, the 2D model displacement became more comparable to the 3D model.

Ort, förlag, år, upplaga, sidor
Taylor & Francis, 2019. Vol. 14, nr 6, s. 392-403
Nyckelord [en]
Cross laminated timber, finite element analysis, board width, out-of-plane loading
Nationell ämneskategori
Trävetenskap Annan maskinteknik
Forskningsämne
Träteknik
Identifikatorer
URN: urn:nbn:se:ltu:diva-73140DOI: 10.1080/17480272.2019.1587506ISI: 000489177400002Scopus ID: 2-s2.0-85062711678OAI: oai:DiVA.org:ltu-73140DiVA, id: diva2:1294670
Anmärkning

Validerad;2019;Nivå 2;2019-10-10 (johcin)

Tillgänglig från: 2019-03-08 Skapad: 2019-03-08 Senast uppdaterad: 2019-10-28Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Personposter BETA

Berg, SvenTuresson, JonasEkevad, MatsHuber, Johannes Albert Josef

Sök vidare i DiVA

Av författaren/redaktören
Berg, SvenTuresson, JonasEkevad, MatsHuber, Johannes Albert Josef
Av organisationen
Träteknik
I samma tidskrift
Wood Material Science & Engineering
TrävetenskapAnnan maskinteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 229 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf