Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Impact of board width on in-plane shear stiffness of cross-laminated timber
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknik.ORCID-id: 0000-0002-0900-5110
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknik.ORCID-id: 0000-0002-4686-4010
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Träteknik.ORCID-id: 0000-0002-0145-080x
2019 (Engelska)Ingår i: Engineering structures, ISSN 0141-0296, E-ISSN 1873-7323, Vol. 196, artikel-id 109249Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Board width-to-thickness ratios in non-edge-glued cross laminated timber (CLT) panels influence the in-plane shear stiffness of the panel. The objective is to show the impact of board width-to-thickness ratios for 3- and 5-layer CLT panels. Shear stiffnesses were calculated using finite element analysis and are shown as reduction factors relative to the shear stiffnesses of edge-glued CLT panels. Board width-to-thickness ratios were independently varied for outer and inner layers. Results show that the reduction factor lies in the interval of 0.6 to 0.9 for most width-to-thickness ratios. Results show also that using boards with low width-to-thickness ratios give low reduction factors. The calculated result differed by 2.9% compared to existing experimental data.

Ort, förlag, år, upplaga, sidor
Elsevier, 2019. Vol. 196, artikel-id 109249
Nyckelord [en]
CLT, In-plane shear modulus, In-plane shear stiffness, Finite element method, CLT board width, CLT layer thickness, CLT shear modulus, Board gap
Nationell ämneskategori
Husbyggnad Annan maskinteknik
Forskningsämne
Träteknik
Identifikatorer
URN: urn:nbn:se:ltu:diva-75098DOI: 10.1016/j.engstruct.2019.05.090ISI: 000482518700013Scopus ID: 2-s2.0-85067851120OAI: oai:DiVA.org:ltu-75098DiVA, id: diva2:1332156
Anmärkning

Validerad;2019;Nivå 2;2019-07-05 (johcin)

Tillgänglig från: 2019-06-27 Skapad: 2019-06-27 Senast uppdaterad: 2021-04-14Bibliografiskt granskad
Ingår i avhandling
1. In-Plane Shear Modulus of Cross-Laminated Timber
Öppna denna publikation i ny flik eller fönster >>In-Plane Shear Modulus of Cross-Laminated Timber
2021 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

Cross-laminated timber (CLT) is a building component used in walls, floors, roofs, or beams in a building. The advantages of using CLT as a building component are, among others, its high load-carrying capability and the possibility of pre-fabrication. The in-plane shear properties of a CLT panel are the in-plane shear modulus and in-plane shear load carrying capacity. This thesis is solely about the in-plane shear modulus and is intended to increase the understanding about the in-plane shear modulus of CLT panels. The in-plane shear modulus is important and there is a need to better understand and estimate its value. The objective of this work was to contribute to the need of finding a suitable test method to measure the in-plane shear modulus of CLT panels and to find factors affecting the in-plane shear modulus.  Three different methods: the picture frame test, the diagonal compression test and the diaphragm shear test, were used in practice and compared to a theoretical test method, the pure shear test. The three methods were compared by conducting experimental tests and by simulating the methods using finite element (FE). Based on the FE simulations, an equation to calculate the shear modulus was created for each test method.  Results from the FE analyses showed that the picture frame test gave results similar to the theoretical pure shear test models. The reason for this result was that the picture frame test is a biaxial testing method. The diagonal compression test and the diaphragm shear test are uniaxial test method. It was also concluded that the picture frame test has a pure shear state in the measured region. The mean error for the in-plane shear modulus equations was estimated, by comparing results from practical testing and FE simulations, to be -2.5%, +12.6% and +11.8% for the picture frame test, diagonal compression test and diaphragm shear test, respectively. The diagonal compression test was the preferred method to use with respect to its simplicity.The factors having an impact on the in-plane shear modulus were found by comparing multiple FE simulations. The results showed that it is possible to increase the in-plane shear modulus by: increasing the odd numbered layers width-to-thickness ratio; decreasing the odd layers thickness ratio of the CLT panels thickness; increasing the number of layers; reducing the gaps between boards; and using alternative main laminate directions. 

Ort, förlag, år, upplaga, sidor
Luleå: Luleå University of Technology, 2021
Serie
Doctoral thesis / Luleå University of Technology 1 jan 1997 → …, ISSN 1402-1544
Nationell ämneskategori
Annan samhällsbyggnadsteknik Husbyggnad
Forskningsämne
Träteknik
Identifikatorer
urn:nbn:se:ltu:diva-83652 (URN)978-91-7790-823-4 (ISBN)978-91-7790-824-1 (ISBN)
Disputation
2021-06-09, Auditorium A, Skellefteå, 09:00 (Engelska)
Opponent
Handledare
Tillgänglig från: 2021-04-15 Skapad: 2021-04-14 Senast uppdaterad: 2021-05-26Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltextScopus

Person

Turesson, JonasBerg, SvenEkevad, Mats

Sök vidare i DiVA

Av författaren/redaktören
Turesson, JonasBerg, SvenEkevad, Mats
Av organisationen
Träteknik
I samma tidskrift
Engineering structures
HusbyggnadAnnan maskinteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 182 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf