Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Finite element modeling and validation of springback and stress relaxation in the thermo-mechanical forming of thin Ti-6Al-4V sheets
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Material- och solidmekanik. Division Materials and Production, RISE IVF ABRISE Research Institutes of Sweden, Olofström.
Division of Subtractive and Additive Manufacturing, University West, Trollhättan.
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Material- och solidmekanik.ORCID-id: 0000-0001-7074-8960
2019 (Engelska)Ingår i: The International Journal of Advanced Manufacturing Technology, ISSN 0268-3768, E-ISSN 1433-3015, Vol. 104, nr 9-12, s. 3439-3455Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

In this work, a hot forming procedure is developed using computer-aided engineering (CAE) to produce thin Ti-6Al-4V sheet components in an effective way. Traditional forming methods involve time- and cost-consuming furnace heating and subsequent hot sizing steps. A material model for finite element (FE) analyses of sheet metal forming and springback at elevated temperatures in Ti-6Al-4V is calibrated and evaluated. The anisotropic yield criterion proposed by Barlat et al. 2003 is applied, and the time- and temperature-dependent stress relaxation behavior for elastic and inelastic straining are modeled using a Zener–Wert–Avrami formulation. Thermo-mechanical uniaxial tensile tests, a biaxial test, and uniaxial stress relaxation tests are performed and used as experimental reference to identify material model parameters at temperatures up to 700 °C. The hot forming tool setup is manufactured and used to produce double-curved aero engine components at 700 °C with different cycle times for validation purposes. Correlations between the predicted and measured responses such as springback and shape deviation show promising agreement, also when the forming and subsequent holding time was as low as 150 s. The short cycle time resulted in elimination of a detectable alpha case layer. Also, the tool surface coating extends the tool life in combination with a suitable lubricant. 

Ort, förlag, år, upplaga, sidor
Springer, 2019. Vol. 104, nr 9-12, s. 3439-3455
Nyckelord [en]
Hot forming, Stress relaxation, Springback, Ti-6Al-4V, Plastic anisotropy, FE analysis
Nationell ämneskategori
Teknisk mekanik
Forskningsämne
Hållfasthetslära
Identifikatorer
URN: urn:nbn:se:ltu:diva-75356DOI: 10.1007/s00170-019-04071-9ISI: 000500220700016OAI: oai:DiVA.org:ltu-75356DiVA, id: diva2:1338801
Anmärkning

Validerad;2019;Nivå 2;2019-11-27 (johcin)

Tillgänglig från: 2019-07-24 Skapad: 2019-07-24 Senast uppdaterad: 2019-12-20Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Personposter BETA

Odenberger, Eva-LisOldenburg, Mats

Sök vidare i DiVA

Av författaren/redaktören
Odenberger, Eva-LisOldenburg, Mats
Av organisationen
Material- och solidmekanik
I samma tidskrift
The International Journal of Advanced Manufacturing Technology
Teknisk mekanik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 33 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf