Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
The effects of laser irradiation on an aluminium powder stream in Directed Energy Deposition
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Produkt- och produktionsutveckling.ORCID-id: 0000-0002-0649-0130
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Produkt- och produktionsutveckling.ORCID-id: 0000-0003-0194-9018
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Produkt- och produktionsutveckling.ORCID-id: 0000-0002-3569-6795
2021 (engelsk)Inngår i: Additive Manufacturing, ISSN 2214-8604, E-ISSN 2214-7810, Vol. 41, artikkel-id 101968Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

Additive Manufacturing with aluminium alloys is a subject of increasing industrial interest. Directed Energy Deposition using high power lasers and a powder feed is a useful option but the interactions between the powder stream and the laser beam are not completely understood. It is well known that the powder particles heat up in the laser beam and some theoretical models predict that they can reach their vaporisation temperature and have their flight path altered by the associated recoil pressure. In order to learn more about these phenomena, powder streams were observed with a high-speed camera at different laser powers (up to 6 kW) and with three batches of powder (AlSi10Mg) of different particle sizes. The results showed an increase of powder focussing with increased laser power. In addition, some particles were found to disintegrate in the laser beam. It is demonstrated that particle disintegration is most likely to be caused by the momentum induced by the recoil pressure.

sted, utgiver, år, opplag, sider
Elsevier, 2021. Vol. 41, artikkel-id 101968
Emneord [en]
Direct Metal Deposition, recoil pressure, powder disintegration, power attenuation, powder deviation
HSV kategori
Forskningsprogram
Produktionsutveckling
Identifikatorer
URN: urn:nbn:se:ltu:diva-83402DOI: 10.1016/j.addma.2021.101968ISI: 000663107000002Scopus ID: 2-s2.0-85104986249OAI: oai:DiVA.org:ltu-83402DiVA, id: diva2:1539803
Forskningsfinansiär
Vinnova, 2019-04872
Merknad

Validerad;2021;Nivå 2;2021-04-20 (alebob);

Finansiär: EIT Raw Materials (18079)

Tilgjengelig fra: 2021-03-25 Laget: 2021-03-25 Sist oppdatert: 2023-03-07bibliografisk kontrollert
Inngår i avhandling
1. Laser-induced recoil pressure on metal drops and powder particles
Åpne denne publikasjonen i ny fane eller vindu >>Laser-induced recoil pressure on metal drops and powder particles
2021 (engelsk)Licentiatavhandling, med artikler (Annet vitenskapelig)
Abstract [en]

Additive Manufacturing became a major research topic and part of industrial production in the past years. Numerous techniques now allow to build 3D structures with a wide choice of materials. When it comes to processing of metals, a laser beam is often used as a heat source to melt either a wire or powder, where the trajectory of spatters and powder particles can be affected by the laser beam radiation. Laser beam irradiation is partly absorbed by the material, and is then converted to heat, which can cause melting and even vaporization. The vaporization of material induces a recoil pressure on the melt pool, which affects its geometry and dynamics. However, the effects of the recoil pressure on airborne objects such as drops and powder particles are still relatively unknown. Their different sizes and boundary conditions compared to a melt pool might affect their behaviour under high laser beam radiation. 

Therefore, this thesis aims at better understanding the effects of the recoil pressure on metal drops and powder particles, as well as their impacts on Additive Manufacturing processes, especially Directed Energy Deposition and Laser Metal Wire Deposition. In the three adjoined papers, high-speed imaging was used to observe (i) powder blown through a laser beam, (ii) drops falling in a laser beam, and (iii) drops detaching from a wire in a laser beam. The videos enabled to calculate the acceleration of powder particles and drops of different sizes, the density map of the powder stream, and the detachment direction of the drops. The experimental results were completed with theoretical calculations of thermodynamics, recoil pressure and surface tension. 

These studies allowed to conclude that the acceleration induced by the recoil pressure on a drop or a powder particle increases with decreased size. Moreover, the recoil pressure causes a slight deviation of the powder stream in Directed Energy Deposition that can induce a better powder focusing. The recoil pressure can also cause the disintegration of powder particles in the laser beam. Finally, it was shown that the recoil pressure can be used to detach drops on demand from a wire and accelerate them towards the substrate where they can be strategically deposited for building additive structures.

sted, utgiver, år, opplag, sider
Luleå University of Technology, 2021
Serie
Licentiate thesis / Luleå University of Technology, ISSN 1402-1757
HSV kategori
Forskningsprogram
Produktionsutveckling
Identifikatorer
urn:nbn:se:ltu:diva-83629 (URN)978-91-7790-817-3 (ISBN)978-91-7790-818-0 (ISBN)
Presentation
2021-06-08, A109, Luleå tekniska Universitet, Luleå, 09:00 (engelsk)
Opponent
Veileder
Tilgjengelig fra: 2021-04-14 Laget: 2021-04-13 Sist oppdatert: 2021-11-02bibliografisk kontrollert
2. Aspects of material and heat transfer in drop- and powder-based laser additive manufacturing
Åpne denne publikasjonen i ny fane eller vindu >>Aspects of material and heat transfer in drop- and powder-based laser additive manufacturing
2023 (engelsk)Doktoravhandling, med artikler (Annet vitenskapelig)
Abstract [en]

Additive Manufacturing became a major research topic and part of industrial production in the past years. Numerous techniques now allow to build 3D structures with a wide choice of materials. When it comes to processing of metals, a laser beam is often used as a heat source to melt either a wire or powder. Novel approaches of material deposition are also developed, such as Laser Droplet Generation, which could potentially be applied to Additive Manufacturing. During the process, the laser beam light is partly absorbed by the material, and is then converted to heat, which can induce melting and even vaporization. Additive Manufacturing presents several processing challenges, such as the recoil pressure acting on the drops and powder particles that affects their trajectory. Storage and recycling of the powders is also an important aspect since the powder properties are changed through aging. Another challenge is the adjustment of process parameters according to varying deposition conditions, where the use of process monitoring techniques is crucial.

Therefore, this thesis aims at better understanding (i) the effects of recoil pressureon metal drops and powder particles, (ii) powder aging and its effects on the process, and (iii) process optimisation and stability via monitoring. In the six adjoined papers, high-speed imaging and thermal imaging were used to observe laser Additive Manufacturing processes involving both metal drops and powders. The videos enabled to observe drop detachments, measure trajectories, plot powder density maps, quantify powder catchment in the melt pool, measure themelt pool geometry, detect oxides, and extract cooling rates. The experimental results were supplemented with material analysis and theoretical calculations of thermodynamics, recoil pressure and surface tension.

These studies allowed to conclude that the recoil pressure induced by laser irradiation on a drop or a powder particle can have some significant effect such as acceleration, change of trajectory, or disintegration. However, these effects seem to be considerably lower than what theoretical models predict. It was also found that the recoil pressure can be used to accurately detach drops from a wire, which was utilised as a new material deposition method for Additive Manufacturing. In Directed Energy deposition, it was showed that aging of the aluminium powder feedstock should be avoided since it induces high porosity, high dilution and decreased mechanical properties. Finally, to guarantee a defect-free deposition during the whole process, it was demonstrated that a thermal camera can be used to monitor the melt pool size, which allows to apply appropriate laser power adjustments to compensate for changing building conditions.  

sted, utgiver, år, opplag, sider
Luleå: Luleå University of Technology, 2023
Serie
Doctoral thesis / Luleå University of Technology 1 jan 1997 → …, ISSN 1402-1544
HSV kategori
Forskningsprogram
Produktionsutveckling
Identifikatorer
urn:nbn:se:ltu:diva-95798 (URN)978-91-8048-280-6 (ISBN)978-91-8048-281-3 (ISBN)
Disputas
2023-05-03, E632, Luleå tekniska universitet, Luleå, 09:00 (engelsk)
Opponent
Veileder
Tilgjengelig fra: 2023-03-07 Laget: 2023-03-07 Sist oppdatert: 2023-09-01bibliografisk kontrollert

Open Access i DiVA

fulltext(7690 kB)247 nedlastinger
Filinformasjon
Fil FULLTEXT01.pdfFilstørrelse 7690 kBChecksum SHA-512
fd3f37913a9cb006d59a4d643589a62ca8a455535e34a7fc852a6b00ed2234f572dc79ea49e9cddf88b10bd09517edb9bd702ad541a534e92a3609eabcafb925
Type fulltextMimetype application/pdf

Andre lenker

Forlagets fulltekstScopus

Person

Da Silva, AdrienVolpp, JoergKaplan, Alexander F.H.

Søk i DiVA

Av forfatter/redaktør
Da Silva, AdrienVolpp, JoergKaplan, Alexander F.H.
Av organisasjonen
I samme tidsskrift
Additive Manufacturing

Søk utenfor DiVA

GoogleGoogle Scholar
Totalt: 247 nedlastinger
Antall nedlastinger er summen av alle nedlastinger av alle fulltekster. Det kan for eksempel være tidligere versjoner som er ikke lenger tilgjengelige

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 100 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf