Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Time-dependent properties of high-density polyethylene with wood/graphene nanoplatelets reinforcement
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Materialvetenskap.ORCID-id: 0000-0001-5550-2962
Department of Structural Engineering,Riga Technical University, Rīga, Latvia.ORCID-id: 0000-0001-8050-2294
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Maskinelement.ORCID-id: 0000-0001-8676-8819
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Materialvetenskap.ORCID-id: 0000-0002-5210-4341
2023 (Engelska)Ingår i: Polymer Composites, ISSN 0272-8397, E-ISSN 1548-0569, Vol. 44, nr 1, s. 465-479Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The effect of graphene nanoplatelets (GNPs) on the long-term performance of wood fiber/high-density polyethylene (HDPE) composite is investigated by using short-term creep tests with an efficient, faster data analysis approach. Previously, it was shown that the addition of GNPs at 15 wt% into HDPE reduces the viscoplastic (VP) strain developed during 2 h creep by ~50%. The current study shows that 25 and 40 wt% wood content in HDPE reduce the VP strains developed during 2 h creep time by >75% with no noticeable effect of the increased wood content. However, further addition of GNPs results in more than 90% total reduction in the VP strains. The current study shows that the development of the VP strains in the hybrid composites follows Zapas model. Viscoelastic (VE) response of these composites is nonlinear and thus is described by Schapery's model. Parameters for VP and VE models are obtained from the creep experiments and were validated in a separate loading-unloading test sequence. Results show a very good agreement between experiments and predictions for the studied materials as long as the micro-damage is not present.

Ort, förlag, år, upplaga, sidor
John Wiley & Sons, 2023. Vol. 44, nr 1, s. 465-479
Nyckelord [en]
creep, graphene nanoplatelets, multiscale composites, time-dependent properties, viscoelasticity, viscoplasticity, wood fibers
Nationell ämneskategori
Kompositmaterial och -teknik
Forskningsämne
Polymera kompositmaterial; Maskinelement
Identifikatorer
URN: urn:nbn:se:ltu:diva-90137DOI: 10.1002/pc.27110ISI: 000877029700001Scopus ID: 2-s2.0-85141407844OAI: oai:DiVA.org:ltu-90137DiVA, id: diva2:1650790
Forskningsfinansiär
Europeiska regionala utvecklingsfonden (ERUF), 1.1.1.2/VIAA/4/20/646EU, Horisont 2020, 777810 Nano2Day
Anmärkning

Validerad;2023;Nivå 2;2023-04-19 (hanlid);

Tillgänglig från: 2022-04-08 Skapad: 2022-04-08 Senast uppdaterad: 2023-04-19Bibliografiskt granskad
Ingår i avhandling
1. Multifunctionality and Durability of Cellulosic Fiber Reinforced Polymer Composites
Öppna denna publikation i ny flik eller fönster >>Multifunctionality and Durability of Cellulosic Fiber Reinforced Polymer Composites
2022 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Alternativ titel[sv]
Multifunktionalitet och beständighet hos cellulosabaserade fiberkompositer
Abstract [en]

The overall objective of this thesis is to develop and evaluate cellulose-based fiber composites with added multifunctionality for advanced applications. In the strive towards sustainable societies and industries, materials as well as production processes need to be assessed against the sustainability criteria and selected accordingly. Cellulosic fibers reinforced polymer composites are being increasingly used in applications where weight saving, and environmental friendliness is as important as structural performance. Nonetheless, these materials have their limitations regarding durability and stability of the properties, but their potential in use for advanced applications can be expanded if functionalized and considered beyond their structural performance. Such multi-functionality of composites can be achieved by the coating of fibers and/or modifying the matrix with functional reinforcement, or by both of these routes combined. Coating of fibers and modifying the matrix with nano-reinforcement are two selected approaches for imparting functionality to the cellulosic fiber composites in the current study. 

Conductive Regenerated Cellulose Fibers (RCFs) were produced by coating commercial RCFs with copper via electroless plating process. Electrical conductivity and mechanical performance were evaluated, and the coated fibers were transformed into an embedded strains sensor-like assembly that could be used as structural health monitoring system in composites structures. A noticeable degradation in the mechanical strength of fibers was realized and it was attributed to the influence of the chemicals of the final plating step of process on the chains of cellulose as well as the loss of crystalline order in the RCF. 

In order to obtain modified matrix (nanocomposites) for multifunctional wood polymer composites (WPC), the commercial masterbatches based on Graphene Nanoplatelets (GNPs) were utilized by melt extrusion process. Effect of the processing parameters in terms of change in screw configurations and the change in composition of the constituents on the structure and mechanical performance of the nanocomposites was studied.  Results showed that there is insignificant effect of the change in the screw configuration in comparison with the effect of increasing the content of the GNPs. Stronger shear forces did not result in better dispersion of the nanoparticles. Addition of the compatibilizer, on the other hand, resulted in an adverse effect on the properties compared to the formulations where it is absent. The use of GNPs with larger aspect ratio resulted in much better improvement in the mechanical performance. Addition of the nanoparticles did not only improve mechanical performance but also resulted in increased thermal conductivity and diffusivity, especially when micro-scale reinforcement was added because of synergy between wood fibers and the GNPs. This synergy was reflected also in the significant 99% improved wear resistance and the >80% reduction in the creep strains of wood and graphene reinforced composites. 

During the design and selection of materials, quasi-static properties are often used as a selection criterion. However, in reality structures in use are often loaded during lengthy periods of time which are followed by multiple steps of unloading/reloading, depending on the service conditions.  In such cases their time-dependent response becomes more crucial than instantaneous mechanical response. Typically, characterization of these properties requires a lot of time, but it may be significantly shortened if proper modeling and analysis are employed. The effect of addition of GNPs to the polymer and wood composites has been studied experimentally by short term creep tests. The materials showed highly nonlinear response even at very low loading stresses, but the addition of the nanoparticles resulted in a decrease in the nonlinearity and in the irreversible strains due to plasticity. Modelling approaches have been used to extract parameters from experimental data that could be used in predicting long term performance using Zapas model for viscoplasticity and Schapery’s model for nonlinear viscoelasticity. 

Overall, the results of the performed work contribute to enriching the research field with the potential the bio-based composites have to offer in the advanced application and how nano-scale reinforcement can interact synergistically with the micro-sized fibers to improve the overall performance of WPC and under different loading scenarios.  

Ort, förlag, år, upplaga, sidor
Luleå University of Technology, 2022
Serie
Doctoral thesis / Luleå University of Technology 1 jan 1997 → …, ISSN 1402-1544
Nationell ämneskategori
Kompositmaterial och -teknik
Forskningsämne
Polymera kompositmaterial
Identifikatorer
urn:nbn:se:ltu:diva-90138 (URN)978-91-8048-057-4 (ISBN)978-91-8048-058-1 (ISBN)
Disputation
2022-06-09, E632, Universitetsområdet Porsön, Luleå, 12:30 (Engelska)
Opponent
Handledare
Tillgänglig från: 2022-04-08 Skapad: 2022-04-08 Senast uppdaterad: 2022-05-19Bibliografiskt granskad

Open Access i DiVA

fulltext(4259 kB)227 nedladdningar
Filinformation
Filnamn FULLTEXT03.pdfFilstorlek 4259 kBChecksumma SHA-512
f818d9745826c2b02f2e5f070afa5456b18ca961479a99c589c208c6c6dbba4eb5a6ad9044ae9925ff2bf19a9bd09973ecae8754cad51699167e4318034b5b63
Typ fulltextMimetyp application/pdf

Övriga länkar

Förlagets fulltextScopus

Person

Al-Maqdasi, ZainabEmami, NazaninJoffe, Roberts

Sök vidare i DiVA

Av författaren/redaktören
Al-Maqdasi, ZainabPupure, LivaEmami, NazaninJoffe, Roberts
Av organisationen
MaterialvetenskapMaskinelement
I samma tidskrift
Polymer Composites
Kompositmaterial och -teknik

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 293 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 353 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf