Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
The effect of the growth ring orientation on spring-back and set-recovery in surface-densified wood
Luleå University of Technology, Department of Engineering Sciences and Mathematics, Wood Science and Engineering.ORCID iD: 0000-0003-0869-5858
Département Génie Civil 2 , Polytech Clermont, Av. Blaise Pascal – 63178 Aubière Cedex , France.
Luleå University of Technology, Department of Engineering Sciences and Mathematics, Wood Science and Engineering.ORCID iD: 0000-0002-1489-0839
Luleå University of Technology, Department of Engineering Sciences and Mathematics, Wood Science and Engineering.ORCID iD: 0000-0002-4526-9391
2023 (English)In: Holzforschung, ISSN 0018-3830, E-ISSN 1437-434X, Vol. 77, no 6, p. 394-406Article in journal (Refereed) Published
Abstract [en]

Wood under thermo-mechanical densification behaves differently depending on the cross-sectional growth ring orientation (GRO) relative to the direction of compression. This influences the degree of cell damage, but also the shape-memory effects occurring when the compression load is released (spring-back) and when the timber is re-moistened (set-recovery). To study how the GRO influences the shape-memory effects, Scots pine specimens were separated into three distinct groups of GRO (Flat, Inclined, Hybrid) and then thermo-mechanically surface-densified. Spring-back and set-recovery were determined by thickness measurements and by digital image correlation. A GRO parallel to the densified surface, resulted in a low spring-back and a high set-recovery which were uniform over the width of the specimen. Specimens with a GRO between 15 and 45° to the densified surface showed high spring-back and low set-recovery, indicating cell-wall damage. Spring-back mainly occurred in the non-plasticised region immediately below the heated surface region and elasto-plastic rolling-shear deformation along individual growth rings occurred. The GRO of softwood subjected to thermo-mechanical densification determines if an applied load results in rolling shear-deformation or radial compression. This in turn determines where in the cross-section and when in the process the cells deform and if this deformation occurs below or above the glass-transition temperature.

Place, publisher, year, edition, pages
Walter de Gruyter, 2023. Vol. 77, no 6, p. 394-406
Keywords [en]
densification, digital image correlation, rolling shear, shape-memory, wood compression
National Category
Wood Science Other Mechanical Engineering
Research subject
Wood Science and Engineering
Identifiers
URN: urn:nbn:se:ltu:diva-96487DOI: 10.1515/hf-2023-0004ISI: 000967647600001Scopus ID: 2-s2.0-85153381478OAI: oai:DiVA.org:ltu-96487DiVA, id: diva2:1750724
Funder
Luleå University of Technology, CT WOOD
Note

Validerad;2023;Nivå 2;2023-06-29 (sofila);

Available from: 2023-04-14 Created: 2023-04-14 Last updated: 2025-01-28Bibliographically approved
In thesis
1. Advancing Continuous Surface Densification of Wood: Process Development, Material Characterisation, and Digital Integration
Open this publication in new window or tab >>Advancing Continuous Surface Densification of Wood: Process Development, Material Characterisation, and Digital Integration
2025 (English)Doctoral thesis, comprehensive summary (Other academic)
Alternative title[sv]
Framsteg inom Kontinuerlig Ytkomprimering av Trä : Processutveckling, Materialkarakterisering och Digital Integrering
Abstract [en]

Surface densification of wood enhances the density and mechanical properties of the surface layer, increasing the value of underutilised wood species and expanding their suitability for a broader range of applications. By improving attributes such as strength and hardness, this process positions densified wood as a sustainable alternative to conventional materials such as plastics, metals and tropical hardwoods. However, despite decades of research, widespread commercial adoption remains limited, due to high production costs, variability in product performance, and the complexities of scaling densification methods for industrial use. 

This thesis addresses key barriers to industrial-scale adoption of surface-densified solid wood intended for flooring, with a focus on continuous densification processes and the optimisation of material properties. Specifically, the research aimed to: (1) evaluate the feasibility of continuous densification using a custom-designed belt press, (2) investigate the influence of growth ring orientation and knots on the densification process and resulting material quality, and (3) establish methods for characterising and optimising density profiles to improve mechanical performance and reliability of product properties.

The belt press studies demonstrated the potential for high-throughput continuous densification, achieving targeted density profiles while minimising non-value-adding steps. Pre-heating and increased heat transfer during compression were identified as critical for mitigating undesired densification and ensuring efficient plasticisation. The influence of growth ring orientation revealed significant variability in strain distribution and spring-back behaviour, underscoring the need for customised material selection and process parameters. These findings are particularly relevant for utilising low-quality or fast-growing wood species as they exhibit high variation in those features.

Mechanical characterisation of surface-densified wood revealed a strong correlation between density profiles and hardness, with the indentation depth during hardness tests shown to be significantly influenced by the density distribution beneath the surface. This relationship shows limitations in traditional hardness testing methods, which may fail to accurately assess performance due to variability in density profiles. To address these challenges, the study proposed an application-focused approach to testing the hardness of surface-densified wood, where the densification process and hardness test parameters are tailored to meet specific end-use requirements rather than relying on arbitrary mechanical metrics. Additionally, a method for predicting density profiles from hardness test data was developed, offering a practical alternative to X-ray densitometry for process control and design.

The development of machine learning models for predicting density profiles from photographic images of the materials’ cross-section offers a method for real-time quality assessment which is industry-suited. By combining this approach with the established correlation between density profiles and hardness, it may become possible to predict hardness solely from images. This integration of digital tools advances data-driven manufacturing in wood densification, providing scalable solutions.

To gain further insights into the densification process, an innovative in-situ measurement technique was developed, combining digital image correlation and computed tomography scanning (CT). This method enabled real-time analysis of density distribution changes during thermo-mechanical densification by aligning 2D strain fields with CT data and employing a constitutive model to estimate density profiles. The method was validated against experimental results and can be used in research, process optimisation, and to provide local density data to refine numerical models for precise and application-specific simulations.

This work bridges scientific principles with industrial practice, providing a foundation for the commercialisation of surface-densified wood products. By addressing critical challenges in process efficiency, material variability, and characterisation, this thesis lays the groundwork for large-scale industrial production of surface-densified flooring boards. 

Place, publisher, year, edition, pages
Luleå: Luleå University of Technology, 2025
Series
Doctoral thesis / Luleå University of Technology 1 jan 1997 → …, ISSN 1402-1544
Keywords
densification, density profile, continuous process, hardness
National Category
Wood Science
Research subject
Wood Science and Engineering
Identifiers
urn:nbn:se:ltu:diva-111448 (URN)978-91-8048-744-3 (ISBN)978-91-8048-745-0 (ISBN)
Public defence
2025-03-27, A193, Luleå University of Technology, Skellefteå, 09:00 (English)
Opponent
Supervisors
Available from: 2025-01-29 Created: 2025-01-28 Last updated: 2025-01-29Bibliographically approved

Open Access in DiVA

fulltext(5311 kB)141 downloads
File information
File name FULLTEXT02.pdfFile size 5311 kBChecksum SHA-512
f571697758a42d228e336d0596a066250d4cb01bae66b13ba631a1d738d6bacb70b0b665ea0d596d3df708d550735cd99daca963a69b394227a98d1362751f6c
Type fulltextMimetype application/pdf

Other links

Publisher's full textScopus

Authority records

Scharf, AlexanderNeyses, BenediktSandberg, Dick

Search in DiVA

By author/editor
Scharf, AlexanderNeyses, BenediktSandberg, Dick
By organisation
Wood Science and Engineering
In the same journal
Holzforschung
Wood ScienceOther Mechanical Engineering

Search outside of DiVA

GoogleGoogle Scholar
Total: 174 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 279 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf