Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Microstructure of NiAl-Ta-Cr in situ alloyed by induction-assisted laser-based directed energy deposition
Department of Additive Manufacturing and Printing, Fraunhofer Institute for Material and Beam Technology, Winterbergstraße 28, 01277 Dresden, Germany; Institute of Materials Science, Faculty of Mechanical Science and Engineering, TUD Dresden University of Technology, Helmholtzstr. 7, 01069 Dresden, Germany.
Institute of Materials Science, Faculty of Mechanical Science and Engineering, TUD Dresden University of Technology, Helmholtzstr. 7, 01069 Dresden, Germany.ORCID-id: 0000-0003-1371-593X
Department of Additive Manufacturing and Printing, Fraunhofer Institute for Material and Beam Technology, Winterbergstraße 28, 01277 Dresden, Germany; Institute of Materials Science, Faculty of Mechanical Science and Engineering, TUD Dresden University of Technology, Helmholtzstr. 7, 01069 Dresden, Germany.
Department of Additive Manufacturing and Printing, Fraunhofer Institute for Material and Beam Technology, Winterbergstraße 28, 01277 Dresden, Germany.
Vise andre og tillknytning
2024 (engelsk)Inngår i: Materials & design, ISSN 0264-1275, E-ISSN 1873-4197, Vol. 238, artikkel-id 112667Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

The development of new high temperature materials for coatings as well as structural components is an important topic to contribute to a higher efficiency and sustainability of e.g. gas turbine engines. One promising new class of high temperature materials are NiAl-based alloys. Within this study, the microstructure and microhardness of NiAl-Ta-Cr alloys with varying Cr and Ta content were investigated. Graded specimens were fabricated by laser-based directed energy deposition utilizing an in situ alloying approach by mixing elemental Ta and Cr as well as pre-alloyed NiAl powder. Thermodynamic calculations were performed to design the alloy compositions beforehand. Inductive preheating of the substrate was used to counter the challenge of cracking due to the high brittleness. The results show that the cracking decreases with increasing preheating temperature. However, even at 700 °C, the cracking cannot be fully eliminated. Scanning electron microscopy, X-ray diffraction and electron backscatter diffraction revealed the formation of the phases B2-NiAl, A2-Cr and C14-NiAlTa within NiAl-Ta and NiAl-Cr alloys. For NiAl-Ta-Cr compositions, deviations regarding the phase formation between calculation and experiment were observed. Maximum hardness values were achieved within the NiAl-Ta and NiAl-Ta-Cr systems for the eutectic compositions at 14 at.-% Ta with maximum values above 900 HV0.1.

sted, utgiver, år, opplag, sider
Elsevier Ltd , 2024. Vol. 238, artikkel-id 112667
Emneord [en]
Additive manufacturing, Advanced materials, Direct energy deposition, In situ alloying, Intermetallics, Nickel aluminide
HSV kategori
Forskningsprogram
Produktionsutveckling
Identifikatorer
URN: urn:nbn:se:ltu:diva-104289DOI: 10.1016/j.matdes.2024.112667Scopus ID: 2-s2.0-85183602891OAI: oai:DiVA.org:ltu-104289DiVA, id: diva2:1837880
Merknad

Validerad;2024;Nivå 2;2024-04-02 (joosat);

Funder: German Research Foundation (Deutsche Forschungsgemeinschaft, DFG), (457729030);

Full text license: CC BY-NC-ND

Tilgjengelig fra: 2024-02-15 Laget: 2024-02-15 Sist oppdatert: 2024-04-02bibliografisk kontrollert

Open Access i DiVA

fulltext(18056 kB)60 nedlastinger
Filinformasjon
Fil FULLTEXT01.pdfFilstørrelse 18056 kBChecksum SHA-512
edcb74bbd0a1acd38fbc037448b313356b2ae3f588b1557959bd3c68162e7d32c46889e6b47530a3d34025d75e139bd55fe31611bcf5ca510119443fc242c777
Type fulltextMimetype application/pdf

Andre lenker

Forlagets fulltekstScopus

Person

Brueckner, Frank

Søk i DiVA

Av forfatter/redaktør
Enghardt, StefanBrueckner, FrankLeyens, Christoph
Av organisasjonen
I samme tidsskrift
Materials & design

Søk utenfor DiVA

GoogleGoogle Scholar
Totalt: 61 nedlastinger
Antall nedlastinger er summen av alle nedlastinger av alle fulltekster. Det kan for eksempel være tidligere versjoner som er ikke lenger tilgjengelige

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 88 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf