Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Microstructure of NiAl-Ta-Cr in situ alloyed by induction-assisted laser-based directed energy deposition
Department of Additive Manufacturing and Printing, Fraunhofer Institute for Material and Beam Technology, Winterbergstraße 28, 01277 Dresden, Germany; Institute of Materials Science, Faculty of Mechanical Science and Engineering, TUD Dresden University of Technology, Helmholtzstr. 7, 01069 Dresden, Germany.
Institute of Materials Science, Faculty of Mechanical Science and Engineering, TUD Dresden University of Technology, Helmholtzstr. 7, 01069 Dresden, Germany.ORCID-id: 0000-0003-1371-593X
Department of Additive Manufacturing and Printing, Fraunhofer Institute for Material and Beam Technology, Winterbergstraße 28, 01277 Dresden, Germany; Institute of Materials Science, Faculty of Mechanical Science and Engineering, TUD Dresden University of Technology, Helmholtzstr. 7, 01069 Dresden, Germany.
Department of Additive Manufacturing and Printing, Fraunhofer Institute for Material and Beam Technology, Winterbergstraße 28, 01277 Dresden, Germany.
Visa övriga samt affilieringar
2024 (Engelska)Ingår i: Materials & design, ISSN 0264-1275, E-ISSN 1873-4197, Vol. 238, artikel-id 112667Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

The development of new high temperature materials for coatings as well as structural components is an important topic to contribute to a higher efficiency and sustainability of e.g. gas turbine engines. One promising new class of high temperature materials are NiAl-based alloys. Within this study, the microstructure and microhardness of NiAl-Ta-Cr alloys with varying Cr and Ta content were investigated. Graded specimens were fabricated by laser-based directed energy deposition utilizing an in situ alloying approach by mixing elemental Ta and Cr as well as pre-alloyed NiAl powder. Thermodynamic calculations were performed to design the alloy compositions beforehand. Inductive preheating of the substrate was used to counter the challenge of cracking due to the high brittleness. The results show that the cracking decreases with increasing preheating temperature. However, even at 700 °C, the cracking cannot be fully eliminated. Scanning electron microscopy, X-ray diffraction and electron backscatter diffraction revealed the formation of the phases B2-NiAl, A2-Cr and C14-NiAlTa within NiAl-Ta and NiAl-Cr alloys. For NiAl-Ta-Cr compositions, deviations regarding the phase formation between calculation and experiment were observed. Maximum hardness values were achieved within the NiAl-Ta and NiAl-Ta-Cr systems for the eutectic compositions at 14 at.-% Ta with maximum values above 900 HV0.1.

Ort, förlag, år, upplaga, sidor
Elsevier Ltd , 2024. Vol. 238, artikel-id 112667
Nyckelord [en]
Additive manufacturing, Advanced materials, Direct energy deposition, In situ alloying, Intermetallics, Nickel aluminide
Nationell ämneskategori
Metallurgi och metalliska material Bearbetnings-, yt- och fogningsteknik
Forskningsämne
Produktionsutveckling
Identifikatorer
URN: urn:nbn:se:ltu:diva-104289DOI: 10.1016/j.matdes.2024.112667Scopus ID: 2-s2.0-85183602891OAI: oai:DiVA.org:ltu-104289DiVA, id: diva2:1837880
Anmärkning

Validerad;2024;Nivå 2;2024-04-02 (joosat);

Funder: German Research Foundation (Deutsche Forschungsgemeinschaft, DFG), (457729030);

Full text license: CC BY-NC-ND

Tillgänglig från: 2024-02-15 Skapad: 2024-02-15 Senast uppdaterad: 2024-04-02Bibliografiskt granskad

Open Access i DiVA

fulltext(18056 kB)59 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 18056 kBChecksumma SHA-512
edcb74bbd0a1acd38fbc037448b313356b2ae3f588b1557959bd3c68162e7d32c46889e6b47530a3d34025d75e139bd55fe31611bcf5ca510119443fc242c777
Typ fulltextMimetyp application/pdf

Övriga länkar

Förlagets fulltextScopus

Person

Brueckner, Frank

Sök vidare i DiVA

Av författaren/redaktören
Enghardt, StefanBrueckner, FrankLeyens, Christoph
Av organisationen
Produkt- och produktionsutveckling
I samma tidskrift
Materials & design
Metallurgi och metalliska materialBearbetnings-, yt- och fogningsteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 60 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 88 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf