Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Wet clutch friction characteristics obtained from simplified pin on disc test
Luleå tekniska universitet, Institutionen för teknikvetenskap och matematik, Maskinelement.ORCID-id: 0000-0001-9110-2819
2008 (engelsk)Inngår i: Tribology International, ISSN 0301-679X, E-ISSN 1879-2464, Vol. 41, nr 9-10, s. 824-830Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

The frictional behavior of wet clutches in vehicle drivetrains is critical for their overall behavior. During the development of new wet clutch systems there is a need to know this friction behavior. The transferred torque is normally investigated in test rigs where the friction in a sliding interface between a friction disc and separator disc is investigated. These test rigs can be designed differently, depending on the working conditions of the investigated clutch. However, it is possible today to simulate the clutch behavior and not limit ourselves to only using measurements from test rigs for the design of the wet clutch. The torque transferred by the clutch during engagement can be roughly divided into full film torque and boundary lubrication torque. The full film regime is possible to simulate quite well, whereas the friction in the boundary regime is much more difficult to simulate due to its strong additive dependency. To obtain a good prediction of the total engagement, friction measurements in the boundary lubrication regime are still needed. These measurements should be easy to perform and fast tests are preferable. Friction coefficients for the whole range of sliding speed, interface temperature and nominal surface pressure should be measured. To use these measurements in simulations and get a better understanding of the friction behavior, it is also preferable to conduct these measurements on a small test sample, for which the temperature and sliding speed can be regarded as constant.Here, the friction of a small sample of a wet clutch friction disc is investigated in a pin on disc test and the temperature is measured in the sample during the tests. Measurements are compared with measurements from a test rig for whole friction discs. A good correspondence between the frictional behaviors of the different measurement methods is achieved.

sted, utgiver, år, opplag, sider
2008. Vol. 41, nr 9-10, s. 824-830
HSV kategori
Forskningsprogram
Maskinelement
Identifikatorer
URN: urn:nbn:se:ltu:diva-5331DOI: 10.1016/j.triboint.2007.11.014ISI: 000257736800002Scopus ID: 2-s2.0-44749090015Lokal ID: 36627010-3c3f-11dd-8e42-000ea68e967bOAI: oai:DiVA.org:ltu-5331DiVA, id: diva2:978205
Merknad
Validerad; 2008; Bibliografisk uppgift: 12th Nordic Symposium on Tribology, NORDTRIB 2006; 20080617 (rola)Tilgjengelig fra: 2016-09-29 Laget: 2016-09-29 Sist oppdatert: 2018-07-10bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekstScopus

Personposter BETA

Marklund, PärLarsson, Roland

Søk i DiVA

Av forfatter/redaktør
Marklund, PärLarsson, Roland
Av organisasjonen
I samme tidsskrift
Tribology International

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 111 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf