Endre søk
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Microstructure and property evolution during the sintering of stainless steel alloy with Si 3 N 4
Department of Metallurgical and Materials Engineering, University of Engineering and Technology, Lahore.ORCID-id: 0000-0003-4888-6237
School of Materials Science and Engineering, China University of Mining and Technology, Xuzhou.
Institute of Powder Metallurgy, School of Materials Science and Engineering, University of Science and Technology, Beijing.
Institute of Powder Metallurgy, School of Materials Science and Engineering, University of Science and Technology, Beijing.
Vise andre og tillknytning
2008 (engelsk)Inngår i: Materials Science & Engineering: A, ISSN 0921-5093, E-ISSN 1873-4936, Vol. 472, nr 1-2, s. 324-331Artikkel i tidsskrift (Fagfellevurdert) Published
Abstract [en]

This paper describes the sintering of a martensitic stainless steel alloy with addition of Si3N4. Sintering behavior was studied at different sintering temperatures ranging from 1250 to 1400 °C with different holding times (20–80 min) and with varying Si3N4. Results showed that the samples were densified rapidly via liquid phase sintering mechanism. Nearly full density was obtained at 1300 °C after 60 min of holding time with 5 wt% Si3N4. Temperature above 1350 °C and Si3N4 content 10 wt% caused slumping of the samples. Two weight percent Si3N4 was found chemically stable in steel alloy. Above 2 wt% Si3N4 dissolved in the steel matrix. The distribution of dissolved Si and N was characterized by XMAP. When N content reached much above its solubility limit in steel alloy it diffused out leaving pores in steel alloy with considerable decrease in the sintered density. The mechanical properties of the sintered product with varying Si3N4 were measured. A maximum ultimate tensile strength of 1011 MPa was achieved with 2 wt% Si3N4 sintered at 1300 °C after 60 min of holding time. Fracture morphologies of tensile samples are also reported.

sted, utgiver, år, opplag, sider
2008. Vol. 472, nr 1-2, s. 324-331
HSV kategori
Forskningsprogram
Materialteknik
Identifikatorer
URN: urn:nbn:se:ltu:diva-14913DOI: 10.1016/j.msea.2007.04.032Lokal ID: e5a825b5-8bb0-40df-96fa-737e56918dd8OAI: oai:DiVA.org:ltu-14913DiVA, id: diva2:987886
Merknad
Upprättat; 2008; 20150416 (farakh)Tilgjengelig fra: 2016-09-29 Laget: 2016-09-29 Sist oppdatert: 2017-11-24bibliografisk kontrollert

Open Access i DiVA

Fulltekst mangler i DiVA

Andre lenker

Forlagets fulltekst

Personposter BETA

Akhtar, Farid

Søk i DiVA

Av forfatter/redaktør
Akhtar, Farid
I samme tidsskrift
Materials Science & Engineering: A

Søk utenfor DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric

doi
urn-nbn
Totalt: 110 treff
RefereraExporteraLink to record
Permanent link

Direct link
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Annet format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annet språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf