Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
Process Control Maps to Design an Ultra-High Strength-Ductile Steel
Luleå University of Technology, Department of Engineering Sciences and Mathematics, Material Science.ORCID iD: 0000-0002-5390-7701
Luleå University of Technology.
Luleå University of Technology, Department of Engineering Sciences and Mathematics, Material Science.ORCID iD: 0000-0002-9100-7982
University of Saarland .
2019 (English)In: Materials Science and Technology, ISSN 0267-0836, E-ISSN 1743-2847, Vol. 35, no 10, p. 1173-1184Article in journal (Refereed) Published
Place, publisher, year, edition, pages
Taylor & Francis, 2019. Vol. 35, no 10, p. 1173-1184
Keywords [en]
ultrahigh strength, high carbon low alloy steel, Q&P, ductility, map
National Category
Metallurgy and Metallic Materials Other Materials Engineering
Research subject
Engineering Materials
Identifiers
URN: urn:nbn:se:ltu:diva-73102DOI: 10.1080/02670836.2019.1615752ISI: 000469142200001Scopus ID: 2-s2.0-85066881284OAI: oai:DiVA.org:ltu-73102DiVA, id: diva2:1293405
Note

Validerad;2019;Nivå 2;2019-06-19 (johcin)

Available from: 2019-03-04 Created: 2019-03-04 Last updated: 2019-06-19Bibliographically approved
In thesis
1. Increasing phase transformation rate in advanced high strength steel applications
Open this publication in new window or tab >>Increasing phase transformation rate in advanced high strength steel applications
2019 (English)Doctoral thesis, comprehensive summary (Other academic)
Alternative title[sv]
Ökning avfasomvandlingshastigheten för avancerade höghållfasta stål
Abstract [en]

The bainite transformation rate has been shown to increase by starting the heat treatment with partial martensite transformation after austenitization. Based on this fact, a process very similar to “Quenching and Partitioning” (Q&P) is used to produce a fine-grained complex microstructure of martensite, bainite and retained austenite with outstanding mechanical properties in a very short time. During this process, different mechanisms including bainite transformation, carbon partitioning, carbide precipitation, grain growth may occur. All these mechanisms can affect the mechanical properties such as strength, ductility and toughness. Investigation of the different mechanisms influencing the properties and subsequent optimization of these is important. In this work, different mechanisms of the Q&P heat treatment process and its practical industrial applications have been investigated. 

Firstly, the implementation of a Q&P method directly after laser welding for a few seconds to substitute any post welding treatment has been studied. To investigate the feasibility, limitations, and advantages of this method for a low-carbon low-silicon high strength steel, the microstructure and mechanical properties by both modelling and experimental approach were studied. Promising results show that this method can decrease the ordinary post-welding treatment time from a few minutes to a few seconds, and in addition improve the mechanical properties of the fusion zone and the heat affected zone to the same or even higher values in comparison with the base material.

In the second part of this work, the effect of quenching and partitioning on the microstructure and mechanical properties of a high carbon steel has been studied. The aim with this part was to optimize the phase transformation rate for production of ultra-high strength steel by controlling its microstructural evolution. The results show that it is possible to get good strength values also for high carbon steels by Q&P treatment. In addition, the approach with process control maps can give a good overview of which properties can be achieved by this method. Hardness value of over 700 HV, and tensile strength of up to 2.5 GPa with a relatively good ductility of 4-6% has been achieved by quenching to room temperature and partitioning for less than one minute at 400 °C resulting in a microstructure consisting of martensite and retained austenite. In a nutshell, the approach to bainite transformation with pre-existing martensite shorten the processing time for development of advanced high strength steels significantly. This method is also possible to be used in industrial processes as in welding.

Place, publisher, year, edition, pages
Luleå: Luleå University of Technology, 2019
Series
Doctoral thesis / Luleå University of Technology 1 jan 1997 → …, ISSN 1402-1544
Keywords
Advanced high strength steel, Quenching and partitioning, welding
National Category
Metallurgy and Metallic Materials Other Materials Engineering
Research subject
Engineering Materials
Identifiers
urn:nbn:se:ltu:diva-72569 (URN)978-91-7790-324-6 (ISBN)978-91-7790-325-3 (ISBN)
Public defence
2019-05-10, E231, Luleå, 10:00 (English)
Opponent
Supervisors
Note

This thesis is the result of a collaboration between Luleå University of Technology and Saarland University that aims toward a double degree.

Available from: 2019-03-05 Created: 2019-03-04 Last updated: 2019-04-16Bibliographically approved

Open Access in DiVA

No full text in DiVA

Other links

Publisher's full textScopus

Authority records BETA

Forouzan, FarnooshVuorinen, Esa

Search in DiVA

By author/editor
Forouzan, FarnooshBorasi, LucianoVuorinen, Esa
By organisation
Material ScienceLuleå University of Technology
In the same journal
Materials Science and Technology
Metallurgy and Metallic MaterialsOther Materials Engineering

Search outside of DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetric score

doi
urn-nbn
Total: 67 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • harvard1
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf