Change search
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf
An Approach for Evaluation of Brick Lining's Mechanical State in Rotary Kilns
Luleå University of Technology, Department of Engineering Sciences and Mathematics, Mechanics of Solid Materials.ORCID iD: 0000-0002-2825-8543
2018 (English)Doctoral thesis, comprehensive summary (Other academic)Alternative title
Utvärdering av tegelinfodringensmekaniska tillstånd i roterugnar (Swedish)
Abstract [en]

Production of many materials requires treatment at elevated temperatures. Calcination and sintering are some of the important heat treatment procedures which are typically performed in so-called rotary kilns. These, not very well-known treatment vessels, have a significant impact on our everyday life. Our most common materials have direct con-nection to the use of rotary kilns. Concrete−covering the vast 80 wt% of total material production in the world−consists to a large part of cement produced in a rotary kiln. Steel−by far the most produced metal−frequently starts its journey in a rotary kiln in form of iron-ore pellets. Paper−another everyday life product−is dependent on mineral lime that is typically calcinated in a rotary kiln. The importance of rotary kilns in our society cannot be doubted.

The concept of a rotary kiln is rather simple. It consists of a thick cylinder-formed steel casing that, due to high process temperatures, is insulated by a refractory lining. Service conditions inside the rotary kiln are rough and the refractory lining is continuously degrading, especially pronounced in the hot zone of the rotary kiln. If the lining is significantly deteriorated and can no longer protect the casing from the heat−the production is shut-down−leading to very high production losses.

Despite many improvements of rotary kilns in the past decades, there is still a gap in the knowledge regarding refractory linings during usage. Many assumptions are based on practical knowledge. One explanation to this could be the difficulty to study and observe the lining due to the large sizes of rotary kilns and high operating temperatures. Today, computers are of a great help for studying various issues without causing production delays or risking failures. However, the field of rotary kilns has stagnated on this matter and little documentation can be found regarding numerical simulations of the refractory lining for rotary kilns, especially of the thermomechanical character.

The aim of this thesis work was to create a numerical model of a rotary kiln usedin iron-ore pelletizing for studying the mechanical and thermomechanical behaviour of refractory brick lining. For this, a simplified finite element model (FEM) of a rotary kiln was created and its trustworthiness verified. It was confirmed that the model gives agood response. Different tips and justifications in the creation of the model of the rotary kiln are given. Furthermore, some mechanical material tests were performed for data input into the model. Various fundamental cases were studied in cold and hot states of the rotary kiln. It was shown that critical situations affecting the brick lining could be captured in a satisfactory way. The insight into the behaviour of the brick lining with respect to various parameters opens possibilities for lowering risk of brick lining failure by an improved management of the rotary kiln.

Place, publisher, year, edition, pages
Luleå: Luleå University of Technology, 2018.
Series
Doctoral thesis / Luleå University of Technology, ISSN 1402-1544
National Category
Mechanical Engineering Applied Mechanics
Research subject
Solid Mechanics
Identifiers
URN: urn:nbn:se:ltu:diva-68376ISBN: 978-91-7790-112-9 (print)ISBN: 978-91-7790-113-6 (electronic)OAI: oai:DiVA.org:ltu-68376DiVA, id: diva2:1198129
Public defence
2018-06-13, E632, Luleå, 09:00 (English)
Opponent
Supervisors
Available from: 2018-04-17 Created: 2018-04-16 Last updated: 2025-10-22Bibliographically approved
List of papers
1. FEM investigation of global mechanisms affecting brick lining stability in a rotary kiln in cold state
Open this publication in new window or tab >>FEM investigation of global mechanisms affecting brick lining stability in a rotary kiln in cold state
2016 (English)In: Engineering Failure Analysis, ISSN 1350-6307, E-ISSN 1873-1961, Vol. 59, p. 554-569Article in journal (Refereed) Published
Abstract [en]

Severe degradation of refractory lining in a rotary kiln often leads to very costly production delays. Use of finite element analysis for understanding the mechanisms behind the failure of the lining is poorly reported in this field. To increase the knowledge and to update the field a simplified model of a kiln and a new methodology for studying stability of the lining are suggested. Behaviour of the lining in cold state – in static and dynamic cases – is studied. Influence of ovality, brick's Young's modulus and friction coefficient on stress and brick displacement are evaluated at two rotational speeds. It was found that the induced loads in the lining are harmless regardless of the tested conditions — challenging the traditional beliefs. On the other hand, recorded brick displacements were found to be significantly affected by rotational speed and ovality. Gaps as large as 80 mm could be observed between the bricks and the casing in a worst case scenario. An integrity coefficient was defined in order to quantify overall integrity of the lining.

Place, publisher, year, edition, pages
Elsevier, 2016
National Category
Applied Mechanics
Research subject
Solid Mechanics
Identifiers
urn:nbn:se:ltu:diva-10950 (URN)10.1016/j.engfailanal.2015.10.023 (DOI)000366667800044 ()2-s2.0-84949725970 (Scopus ID)9d7d2c8b-c56d-47bc-b62c-dfa8025908b9 (Local ID)9d7d2c8b-c56d-47bc-b62c-dfa8025908b9 (Archive number)9d7d2c8b-c56d-47bc-b62c-dfa8025908b9 (OAI)
Note

Validerad; 2016; Nivå 2; 20151102 (andbra)

Available from: 2016-09-29 Created: 2016-09-29 Last updated: 2025-10-21Bibliographically approved
2. Characterization of high-alumina refractory bricks and modelling of hot rotary kiln behaviour
Open this publication in new window or tab >>Characterization of high-alumina refractory bricks and modelling of hot rotary kiln behaviour
2017 (English)In: Engineering Failure Analysis, ISSN 1350-6307, E-ISSN 1873-1961, Vol. 79, p. 852-864Article in journal (Refereed) Published
Abstract [en]

Rotary kilns for iron-ore pellets production are highly dependent on a well-functioning refractory brick lining. To improve the long-term capability of the lining, in-situ observations of the bricks' performance are desired, however, the high process temperatures and the size of the kiln make it difficult to study the lining during operation. By using numerical simulations as a tool, some of the problems encountered by the brick lining can be studied. Knowing material properties of the refractory bricks as input in a numerical model is therefore necessary. However, material properties are poorly documented for this type of materials, especially, at elevated temperatures. In this work three commercial aluminasilicate bricks were tested in compression until failure for a temperature range of 25–1300 °C. The purpose was to evaluate compression strength and Young's modulus in compression of the fully burned bricks at a wide range of temperatures. The data was later used for modelling of a hot rotary kiln lined with bricks by using the finite element method, whereupon load state of the lining was evaluated at steady state after the expansion of the system. The objective of the numerical modelling was to investigate trustworthiness of the model and to give insight into the stress levels that can potentially arise. It was found that for all of the investigated brick types the compression strength increased with increased temperature, having a peak in the vicinity of 1000 °C. The maximum increase was between 50 and 150 % for the different brick types. After passing 1100 °C the compression strength rapidly and considerably decreased below its as-received compression strength. Young's modulus was measured to vary between 2 and 10 GPa in the range of up to 1000 °C. The numerical results indicate that severe boundary conditions (expansion of the lining is highly restricted) can potentially lead to compression stress of up to 34 MPa in the brick lining at steady state. However, at these boundary conditions the present tensile stress was only 0.5 MPa, while tensile stresses of close to 3 MPa could be observed in the lining with mild boundary conditions. The authors conclude that the created model is trustworthy and that it has high potential for being used as a tool in further investigations of the lining in hot state.

Place, publisher, year, edition, pages
Elsevier, 2017
National Category
Applied Mechanics Other Materials Engineering
Research subject
Solid Mechanics; Engineering Materials
Identifiers
urn:nbn:se:ltu:diva-63536 (URN)10.1016/j.engfailanal.2017.04.038 (DOI)000405538800068 ()2-s2.0-85020181003 (Scopus ID)
Note

Validerad;2017;Nivå 2;2017-06-14 (rokbeg)

Available from: 2017-05-26 Created: 2017-05-26 Last updated: 2025-10-22Bibliographically approved
3. Modelling of Hot Rotary Kiln
Open this publication in new window or tab >>Modelling of Hot Rotary Kiln
2017 (English)Conference paper, Published paper (Refereed)
National Category
Applied Mechanics
Research subject
Solid Mechanics
Identifiers
urn:nbn:se:ltu:diva-63626 (URN)
Conference
11th European LS-DYNA Conference, Salzburg, Austria, 9-11 May 2017
Available from: 2017-05-31 Created: 2017-05-31 Last updated: 2025-10-22Bibliographically approved
4. Elasticity modulus and strength of two high-alumina refractory bricks at elevated temperatures
Open this publication in new window or tab >>Elasticity modulus and strength of two high-alumina refractory bricks at elevated temperatures
(English)Manuscript (preprint) (Other academic)
National Category
Materials Engineering
Identifiers
urn:nbn:se:ltu:diva-68373 (URN)
Available from: 2018-04-16 Created: 2018-04-16 Last updated: 2025-10-22
5. Influence of heating and cooling rate on the stress state of the brick lining in a rotary kiln using finite element simulations
Open this publication in new window or tab >>Influence of heating and cooling rate on the stress state of the brick lining in a rotary kiln using finite element simulations
2019 (English)In: Engineering Failure Analysis, ISSN 1350-6307, E-ISSN 1873-1961, Vol. 105, p. 98-109Article in journal (Refereed) Published
Abstract [en]

Rotary kilns for iron-ore pellets production are highly dependent on a well-functioned refractory brick lining. To improve the long-term capability of the lining, in-situ observations of the bricks' performance are desired, however, the harsh environment inside the rotary kiln makes it difficult or nearly impossible to study the lining during operation. By using numerical simulations as a tool, some of the problems encountered by the brick lining can be studied without limitation of the extreme conditions.

In this work, stress state of the lining was studied under the influence of different heating and cooling rates, and different brick compaction cases. A finite element model was created for conducting the numerical simulations. The numerical model was calibrated for transient heat transfer. Temperature dependent material properties of the bricks and casing were used as input. The heating and cooling was controlled by temperature prescription on the boundary of the brick lining, while brick lining compaction by defining relative position of the bricks in axial and radial directions.

The conducted numerical simulations showed that considerable tensile stress may appear in a large area of the brick during initial heating stage. The large tensile area corresponds well with the typical circumferential cracks experienced by the bricks. It was demonstrated that the compressive stresses counteract the development of tensile stresses. However, the compressive stresses may become very large in the initial stage of heating. The positive effect of lower heating rate was considerable on the tensile stresses, while influence on the compressive stresses was almost unnoticed. The hypothetical cooling rates showed that very high tensile stresses may occur on the surface of the bricks, potentially leading to surface spalling. Furthermore, it was demonstrated that axial compaction is highly important on the stress development in the lining, which, may not always be followed in practice. As a general conclusion, it is recommended to always achieve a tight compaction of the brick lining and to take measures for lowering the heating and cooling rates.

The conducted work exemplifies behaviour of the brick lining for realistic heat transfer and material properties. The insight into the behaviour gives possibilities to make adjustments and directed investments for lowering risk of brick lining failure.

Place, publisher, year, edition, pages
Elsevier, 2019
Keywords
High temperature, Stress state, Refractory brick lining, Rotary kiln, Finite element method
National Category
Applied Mechanics
Research subject
Solid Mechanics
Identifiers
urn:nbn:se:ltu:diva-68375 (URN)10.1016/j.engfailanal.2019.06.031 (DOI)000496188200009 ()2-s2.0-85068422246 (Scopus ID)
Note

Validerad;2019;Nivå 2;2019-07-08 (johcin)

Available from: 2018-04-16 Created: 2018-04-16 Last updated: 2025-10-22Bibliographically approved

Open Access in DiVA

fulltext(23218 kB)1372 downloads
File information
File name FULLTEXT03.pdfFile size 23218 kBChecksum SHA-512
18e86e67fade4b7c377f9f04ea37d4750f4aeb79d7020f74d00cc096b04177b096e40669bb003f5c70fbfa5caa92e8a5f1406d9127449f67eb3642938c4e139c
Type fulltextMimetype application/pdf

Authority records

Ramanenka, Dmitrij

Search in DiVA

By author/editor
Ramanenka, Dmitrij
By organisation
Mechanics of Solid Materials
Mechanical EngineeringApplied Mechanics

Search outside of DiVA

GoogleGoogle Scholar
Total: 1378 downloads
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

isbn
urn-nbn

Altmetric score

isbn
urn-nbn
Total: 2360 hits
CiteExportLink to record
Permanent link

Direct link
Cite
Citation style
  • apa
  • ieee
  • modern-language-association-8th-edition
  • vancouver
  • Other style
More styles
Language
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Other locale
More languages
Output format
  • html
  • text
  • asciidoc
  • rtf